Flexural Buckling of Steel Angles: Experimental Investigation
Publication: Journal of Structural Engineering
Volume 122, Issue 3
Abstract
Structural steel angles have a wide variety of applications. However, steel angles have not received the attention comparable to heavy shapes such as wide flange sections. For steel angles, flexural buckling strength is the basic design strength, while the torsional-flexural buckling strength is computed in many codes by modifying the design procedure for flexural buckling strength. This paper presents the results of an experimental investigation of 26 hot-rolled steel angles under concentric axial compression failing in flexural buckling. The width-thickness ratios of test specimens ranged from 6 to 16. The slenderness ratios varied from 68 to 188, covering almost the entire practical range. Residual stresses and yield stresses across the cross sections were determined and initial out-of-straightness was measured. These data were used in the development of a column curve reported in a companion paper.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Adluri, S. M. R. (1994). “Studies on steel angle columns,” PhD dissertation, Dept. of Civ. and Envir. Engrg., Univ. of Windsor, Windsor, Ont., Canada.
2.
Adluri, S. M. R., and Madugula, M. K. S. (1996). “Development of column curve for steel angles.”J. Struct. Engrg., ASCE, 122(3), 318–325.
3.
Adluri, S. M. R., and Madugula, M. K. S. (1995). “Residual stresses and initial out-of-straightness of hot-rolled steel angles.”Proc., 1995 Annu. Tech. Session, Struct. Stability Res. Council, Lehigh Univ., Bethlehem, Pa., 353–367.
4.
Adluri, S. M. R., Madugula, M. K. S., and Monforton, G. R.(1992). “Schifflerized angle struts.”J. Struct. Engrg., ASCE, 118(7), 1920–1936.
5.
Al-Sayed, S. H., and Bjorhovde, R.(1989). “Experimental study of single angle columns.”J. Constr. Steel Res., London, England, 12(2), 83–102.
6.
Basilio, O. H. (1986). “Buckling strength prediction equation for angles-probabilistic approach.”Proc., 1st Int. Symp. on Probabilistic Methods Appl. to Electr. Power Sys., Pergamon Press, Oxford, England, 357–364.
7.
Beedle, L. S., and Tall, L.(1960). “Basic column strength.”J. Struct. Div., ASCE, 86(7), 139–173.
8.
Bjorhovde, R. (1972). “Deterministic and probabilistic approaches to the strength of steel columns,” PhD dissertation, Dept. of Civ. Engrg., Lehigh Univ., Bethlehem, Pa.
9.
Design of latticed steel transmission structures ANSI/ASCE 10-90. (1992). ASCE, New York, N.Y.
10.
Elgaaly, M., Dagher, H., and Davids, W.(1991). “Behavior of single angle compression members.”J. Struct. Engrg., ASCE, 117(12), 3720–3741.
11.
Galambos, T. V. (ed.). (1988). Guide to stability design criteria for metal structures. 4th Ed., Wiley Interscience, New York, N.Y.
12.
Galambos, T. V. (1991). “Design of axially loaded compressed angles.”Proc., 1991 Annu. Tech. Session, Struct. Stability Res. Council, Lehigh Univ., Bethlehem, Pa., 353–367.
13.
Guide for design of steel transmission towers; Manual No. 52 (1988). ASCE, New York, N.Y.
14.
Ishida, A. (1968). “Experimental study on column carrying capacity of `SHY' angles.”Yawata Res. Rep. No. 265, Yawata Iron and Steel Co. Ltd., Tokyo, Japan, 8564–8582.
15.
Kennedy, J. B., and Murty, M. K. S.(1972). “Buckling of steel angle and tee struts.”J. Struct. Div., ASCE, 98(11), 2507–2522.
16.
Kitipornchai, S., and Lee, H. W.(1986). “Inelastic experiments on angle and tee struts,”J. Constr. Steel Res., London, England, 6(3), 219–236.
17.
Lenzen, K. H. (1968). “Design formula for the top chord of open web steel joists.”Studies in Engrg. Mech., Rep. No. 27, Univ. of Kansas, Lawrence, Ks.
18.
Load and resistance factor design of single angle members. (1993). American Institute of Steel Construction (AISC), Inc., Chicago, Ill.
19.
Nuttall, N. J., and Adams, P. F. (1970). “Flexural and lateral-torsional buckling strengths of double angle struts.”Struct. Engrg. Rep. No. 30, Dept. of Civ. Engrg., Univ. of Alberta, Edmonton, Albta., Canada.
20.
O'Connor, C. (1955). “Residual stresses and their influence on structural design.”J. Inst. Engrs., Australia, Vol. 27, 313–321.
21.
Recommendations for angles in lattice transmission towers. (1985). Working Group 8.1, Tech. Committee 8, Eur. Convention for Constructional Steelwork (ECCS), Brussels, Belgium.
22.
Specification for allowable stress design of single angle members. (1989), American Institute of Steel Construction (AISC), Inc., Chicago, Ill.
23.
Stang, A. H., and Strickenberg, L. R. (1924). “Results of some compression tests of structural steel angles.” U.S. Bureau of Standards, Technologic Papers No. 218, Govt. Printing Ofc., Washington, D.C.
24.
Tebedge, N., Alpsten, G. A., and Tall, L.(1973). “Residual-stresses measurement by the sectioning method.”Experimental Mech., 13(2), 88–96.
25.
Usami, T. (1971). “Restrained single angle columns under biaxial bending,” PhD dissertation, Civ. and Envir. Engrg. Dept., Washington Univ., St. Louis, Mo.
26.
Wakabayashi, M., and Nonaka, T. (1965). “On the buckling strength of angles in transmission towers.”Bull., Disaster Prevention Res. Inst., Kyoto Univ., Japan, 15(91), Part 2, 1–18.
27.
Yokoo, Y., Wakabayashi, M., and Nonaka, T. (1968). “An experimental study on buckling of angles.”Yawata Res. Rep. No. 265, Yawata Iron and Steel Co., Ltd., Tokyo, Japan, 8543–8563.
Information & Authors
Information
Published In
Copyright
Copyright © 1996 American Society of Civil Engineers.
History
Published online: Mar 1, 1996
Published in print: Mar 1996
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.