Bending Stiffness of Stress‐Laminated Timber Decks with Butt Joints
Publication: Journal of Structural Engineering
Volume 119, Issue 5
Abstract
Stress‐laminated timber bridge decks consist of lumber assemblies transversely posttensioned with high‐strength steel bars. The lumber components contain end‐to‐end butt joints to span the length of the bridge. At any cross section of the bridge, the joints are placed in a regular pattern, with one butt joint in a group of three to five laminae. The presence of butt joints in a bridge deck reduces its longitudinal bending stiffness. Since stress‐laminated timber bridge decks are modeled as orthotropic plates, the actual system stiffness properties are needed in the analysis. This paper presents an analytical‐experimental study to verify existing bending stiffness reduction factors for decks with regular butt‐joint patterns. Forty northern red oak and hickory stress‐laminated beams with three butt joint patterns and subjected to three transverse stress levels are tested in bending, and the experimental responses are correlated with existing theoretical predictions using linear regression analysis. Design recommendations are presented.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Batchelor, B. DeV., Van Dalen, K., Hachborn, A., and Lee, A. (1979). “Structural characteristics of transversely prestressed laminated wood bridge decks.” Rep. OJT‐CRP 8305, Dept. of Civ. Engrg., Queen's Univ., Kingston, Ontario, Canada.
2.
Davalos, J. F., Dickson, B. D., and Salim, H. A. (1991a). “Analysis, design, and construction of modular stress‐laminated T‐system timber bridges.” Tech. paper CFC‐91‐154, Constr. Fac. Ctr., West Virginia Univ., Morgantown, W.Va.
3.
Davalos, J. F., Loferski, J. R., Holzer, S. M., and Yadama, V. (1991b). “Transverse isotropy modeling of 3‐D glulam timber beams.” J. Mat. in Civ. Engrg., ASCE, 3(2), 125–139.
4.
Guide specifications for the design of stress‐laminated wood decks. (1991). Am. Assoc. of State Hwy. and Transp. Officials (AASHTO), Washington, D.C.
5.
Morrison, T. D. (1981). “Orthotropic plate parameters of prestressed laminated wood systems,” MS thesis, Queen's University, Kingston, Ontario, Canada.
6.
Oliva, M. G., and Dimakis, A. (1988). “Behavior of stress‐laminated timber highway bridge.” J. Struct. Engrg., ASCE, 114(8), 1850–1869.
7.
Oliva, M. G., Dimakis, A. G., Ritter, M. A., and Tucmi, R. L. (1990). “Stress‐laminated wood bridge decks, experimental and analytical evolutions.” Rep. FPL‐RP‐495, U.S. Forest Products Lab., Madison, Wis.
8.
Ritter, M. A. (1990). “Timber bridges design, construction, inspection, and maintenance.” The Engineering Management Series, Forest Service, U.S. Dept. of Agr., Washington, D.C.
9.
Sexsmith, R. G., Boyle, P. D., Rovner, B., and Abbott, R. A. (1979). “Load sharing in vertically laminated, post‐tensioned bridge decking.” Technical rep. no. 6, ISSN 0708‐6172, Forintek Canada Corp., Vancouver, B.C., Canada.
10.
“Standard methods of static tests of timber in structural sizes.” (1989). D‐198, ASTM, Philadelphia, Pa.
11.
Taylor, R. J., Batchelor, B. DeV., and Van Dalen, K. (1983). “Prestressed wood bridges.” Structural Research Rep. SRR‐83‐01, Ministry of Transp. and Communications, Ontario, Canada.
Information & Authors
Information
Published In
Copyright
Copyright © 1993 American Society of Civil Engineers.
History
Received: Oct 15, 1992
Published online: May 1, 1993
Published in print: May 1993
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.