T‐Joints in Rectangular Hollow Sections Subject to Combined Actions
Publication: Journal of Structural Engineering
Volume 117, Issue 8
Abstract
An extensive test program on a range of cold‐formed rectangular and square hollow sections subjected to combined bending and concentrated force is described. The concentrated force was applied by welding a square hollow section (called the branch member) to the center of the member under test (called the chord member) and perpendicular to it. The chord member was simply supported with the concentrated force at the center of the span. The span was varied in order to determine the interaction relationship between bending moment and concentrated force. Tests under pure moment and pure concentrated force were performed for control purposes. The ratio of the width of the branch member to the chord member (β) used varied from 0.5 to 1.0 so that failure modes ranging from local bending and buckling of the face of the chord member to web crippling were observed. In addition, the thickness of the chord‐member sections was varied so as to produce a range of section slenderness and failure modes from buckling to yielding. The results are compared with the design procedures in the 1986 AISI Specification, Australian Standard AS1538 of 1988, CIDECT Monograph No. 6 of 1986, and other proposed procedures. In addition, a comparison with plastic mechanism models is provided.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
CIDECT monograph no. 6. (1986). “The strength and behavior of statically loaded welded connections in structural hollow sections.” Comite International pour le Development et I'etude de la Construction Tubulaire, CIDECT, Corby, England.
2.
Cold‐formed steel structures code. (1988). “Australian standard AS 1538.” Standards Association of Australia, Sydney, Australia.
3.
Common unified code of practice for steel structures, Draft. (1983). “Eurocode 3.” Commission of the European Communities (EC), Brussels, Belgium.
4.
European recommendation for the design of light gauge steel members, No. 49. (1987). 1st Ed., “Design of cold‐formed steel sheeting and sections,” European Convention for Constructional Steelwork (ECCS), Brussels, Belgium.
5.
Hasan, S. W., and Hancock, G. J. (1989). “Plastic bending tests of cold‐formed rectangular hollow sections.” J. Australian Inst. of Steel Constr., Sydney, Australia, 23(4), 2–19.
6.
Karren, K. W. (1967). “Corner properties of cold‐formed steel shapes.” J. Struct. Div., ASCE, 93(1), 401–432.
7.
Kato, B. (1980). “T‐joints made of rectangular tubes.” Proc., 5th Int. Specialty Conf. on Cold‐formed Steel Struct., St. Louis, Mo.
8.
Key, P. W., Hasan, S. W., and Hancock, G. J. (1988). “Column behavior of cold‐formed hollow sections.” J. Struct. Engrg., ASCE, 114(2), 390–407.
9.
Load and resistance factor design specification for structural steel buildings. (1986). American Institute of Steel Construction (AISC), Chicago, Ill.
10.
Methods for tensile testing of metals. (1974). “Australian standard AS1391,” Standards Association of Australia, Sydney, Australia.
11.
Packer, J. A. (1984). “Web crippling of rectangular hollow sections.” J. Struct. Engrg., ASCE, 110(10), 2357–2373.
12.
Proc., Int. Symp. on Tubular Struct. (1989). Lappeenranta Univ., Lappeenranta, Finland.
13.
SAA steel structures code. (1984). “Amendment No. 2.” Standards Association of Australia, Sydney, Australia.
14.
Specifications for the design of cold‐formed steel structural members. (1986). American Iron and Steel Institute (AISI), Washington, D.C.
15.
Steel structures for buildings (limit state design): CAN3‐S16.1‐M84. (1984), Canadian Standards Association, Rexdale, Ontario, Canada.
16.
Steel structures. (1990). “Australian standard AS4100.” Standards Association of Australia, Sydney, Australia.
17.
Structural Steel Hollow Sections. (1981). “Australian standard AS1163,” Standards Association of Australia, Sydney, Australia.
18.
Standard test methods and definitions for mechanical testing of steel products, ASTM A370‐89. (1989). American Society for Testing and Materials (ASTM), Philadelphia, Pa.
19.
Structural use of steelwork in building. (1985). “Part 1: Code of practice for design in simple and continuous construction: hot rolled sections: BS5950,” British Standards Institution, London, England.
20.
Structural use of steelwork in building. (1987). “Part 5: Code of practice for design of cold‐formed sections: BS5950,” British Standards Institution, London, England.
21.
Structural welding code—Steel, ANSI/AWS Dl.1‐90. (1990). 10th Ed., American Welding Society (AWS) Inc., Miami, Fla.
22.
Tubeline RHS safe load tables, AS1163 (grade 350). (1984). Tubemakers of Australia Limited, Sydney, Australia.
23.
Zhao, X. L., and Hancock, G. J. (1990). “T‐joints in rectangular hollow sections subject to combined bending and concentrated force.” Research Report, R616, University of Sydney, Sydney, Australia.
Information & Authors
Information
Published In
Copyright
Copyright © 1991 ASCE.
History
Published online: Aug 1, 1991
Published in print: Aug 1991
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.