Moment‐Rotation Functions For Steel Connections
Publication: Journal of Structural Engineering
Volume 117, Issue 6
Abstract
A least‐squares curve‐fitting procedure is shown to provide better accuracy than the previously used method of selected points when fitting Richard‐Abbott and Ramberg‐Osgood functions to experimental moment‐rotation data. Comparisons are presented to show that the Richard‐Abbott function, in dimensionless form, provides fits that are comparable to cubic B‐spline fits and more accurate than Ramberg‐Osgood function fits for common connection types. A multiple‐regression analysis procedure is described that employs the Richard‐Abbott function to derive a standardized connection moment‐rotation function. Its advantage over previously used standardization procedures is that it is able to utilize all available experimental data in the derivation of the standardized function. The latter function is expressed in terms of the geometric parameters for the connection type considered.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Altman, W. G., Jr., Azizinamini, A., Bradburn, J. H., and Radziminski, J. B. (1982). “Moment‐rotation characteristic of semi‐rigid steel beam‐to‐column connections.” Report, Dept. of Civ. Engrg., Univ. of South Carolina, Columbia. S.C.
2.
Ang, K. M., and Morris, G. A. (1984). “Analysis of three‐dimensional frames with flexible beam‐column connections.” Can. J. Civ. Eng., 11(2), 245–254.
3.
Bailey, J. R. (1970). “Strength and rigidity of bolted beam‐to‐column connections.” Proc. Conf. on Joints in Struct., University of Sheffield, 1.
4.
Deming, W. E. (1964). Statistical adjustment of data. Dover Publications Inc., New York, N.Y.
5.
Frye, M. J., and Morris, G. A. (1975). “Analysis of flexibly connected steel frames.” Can. J. Civ. Eng., 2(3), 280–291.
6.
Goverdhan, A. V. (1984). “A collection of experimental moment‐rotation curves and evaluation of prediction equations for semi‐rigid connections,” thesis presented to Vanderbilt University, at Nashville, Tenn., in partial fulfillment of the requirements for the degree of Master of Science.
7.
Jones, W. S., Kirby, P. A., and Nethercot, D. A. (1980). “Effect of semi‐rigid connections on steel column strength.” J. Constr. Steel Res., London, United Kingdom, 1(1), 38–46.
8.
Lipson, S. L. (1968). “Single‐angle and single‐plate beam framing connections.” Proc. Canadian Struct. Engrg. Conf., Canadian Institute of Steel Construction, 141–162.
9.
Lothers, J. E. (1951). “Elastic restraint equation for semi‐rigid connections.” Trans., ASCE, 116, 480–502.
10.
Lui, E. M. (1985). “Effects of connection flexibility and panel zone deformation on behavior of plane steel frames,” thesis presented to Purdue University, at West Lafayette, Indiana, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
11.
Maxwell, S. M., Jenkins, W. M., and Howlett, J. H. (1981). “A theoretical approach to the analysis of connection behaviour.” Joints in structural steelwork. John Wiley and Sons, Inc., New York, N.Y., 2.49–2.70.
12.
Onuah, C., Morris, G., and Attiogbe, E. (1989). “Moment‐rotation behaviour of double web angle connections.” Proc., Canadian Society for Civil Engineering, 1B, 424–444.
13.
Ostrander, J. R. (1970). “An experimental investigation of end plate connections,” thesis presented to the University of Saskatchewan, at Saskatoon, Saskatchewan, Canada, in partial fulfillment of the requirements for the degree of Master of Science.
14.
Ramberg, W., and Osgood, W. R. (1943). “Description of stress‐strain curves by three parameters.” Tech. Report No. 902, Nat. Advisory Committee for Aeronautics, Washington, D.C.
15.
Richard, R. M., and Abbott, B. J. (1975). “Versatile elastic‐plastic stress‐strain formula.” J. Engrg. Mech. Div., ASCE, 101(4), 511–515.
16.
Sommer, W. H. (1969). “Behaviour of welded header plate connections,” thesis presented to the University of Toronto, at Toronto, Canada, in partial fulfillment of the requirements for the degree of Master of Applied Science.
17.
Thompson, L. E., McKee, R. J., and Visintainer, D. A. (1970). An investigation of rotation characteristics of web shear framed connections using A‐36 and A‐441 steels. Department of Civil Engineering, University of Missouri‐Rolla, Rolla, Mo.
Information & Authors
Information
Published In
Copyright
Copyright © 1991 ASCE.
History
Published online: Jun 1, 1991
Published in print: Jun 1991
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.