Iterative FD Solution to Bending of Axisymmetric Conical Shells
Publication: Journal of Structural Engineering
Volume 116, Issue 9
Abstract
A numerical solution is presented for determining the stresses and displacements in complete and truncated conical shells. The method is based on the classical bending theory of thin axisymmetric shells. The governing differential equation for a conical element is presented in terms of the meridional or axial displacement u and the normal displacement w. Then, an iterative finite difference technique is employed to determine the displacements and in turn the stresses. The method is applicable to short and long conical shells having simply supported, clamped, or free edges. The proposed method can easily be extended to tapered conical shells and other types of axisymmetric shells. Results are presented and compared with those of existing solutions.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Au, T., Goodman, L. E., and Newmark, N. M. (1951). “A numerical procedure for the analysis of pressure vessel heads.” Univ. of Illinois Tech. Rept. to Office of Naval Res., Project NR‐035‐183, Dept. of the Navy, Urbana, Ill.
2.
Baker, E. H., Kovalevsky, L., and Rish, F. L. (1972). Structural analysis of shells. McGraw‐Hill, New York, N.Y.
3.
Baltrukonis, J. H. (1959). “Influence coefficients for edge‐loaded short, thin conical frastrums.” J. Appl. Mech., Trans. ASME, 26(2), 241–245.
4.
Flügge, W. (1960). Stresses in shells. Springer‐Verlag, Berlin, W. Germany.
5.
Gaylord, E. H., and Gaylord, C. N. (1984). Design of steel bins for storage of bulk solids, Prentice‐Hall, Inc., Englewood Cliffs, N.J.
6.
Harintho, H. (1986). “Analysis of open conical metal shells with symmetric discontinuities in geometry.” Thesis presented to the Rose‐Hulman Institute of Tech., at Terre‐Haute, Ind., in partial fulfillment of the requirements for the degree of Master of Science.
7.
Harintho, H., and Logan, D. (1988). “Conical shells with discontinuities in geometry.” J. Struct. Engrg., ASCE, 114(1), 231–240.
8.
Horvay, G., Linkaus, C., and Born, J. S. (1956). “Analysis of short thin shells under axisymmetrical edge loading.” J. Appl. Mech., Trans. ASME, 23(Mar.), 68–72.
9.
Kelkar, V. S., and Stewell, R. T. (1987). Fundamentals of the analysis and design of shell structures. Prentice‐Hall, Inc., Englewood Cliffs, N.J.
10.
Kohnke, P. C. (1983). ANSYS engineering analysis system—Theoretical manual. Swanson Analysis Systems, Inc., Houston, PA.
11.
Kraus, H. (1967). Thin elastic shells. John Wiley and Sons, Inc., New York, N.Y.
12.
Roark, R. J., and Young, W. C. (1975). Formulas for stress and strain. Fifth Ed., McGraw‐Hill, New York, N.Y.
13.
Rotter, J. M. (1986). “Recent studies of the stability of light gauge steel silo structures.” Eighth Int. Specialty Conf. on Cold‐Formed Steel Structs., St. Louis, Miss., Nov., 543–562.
14.
Rotter, J. M. (1987). “The buckling and plastic collapse of ring stiffeners at cone/cylinder junctions.” Proc. Int. Colloquium on Stability of Plate and Shell Structs., Ghent, Belgium, Apr., 449–456.
15.
Rotter, M. J., and Teng, J. G. (1989). Discussion of “Conical Shells with Discontinuities in Geometry,” by H. Harintho and D. Logan, J. Struct. Engrg., ASCE, 115(5), 1557–1559.
16.
Taylor, C. E., and Wenk, E., Jr. (1954). “Analysis of stresses in the conical elements of shell structures.” Proc. Second U.S. Nat. Congr. of Appl. Mech., ASME, New York, N.Y., 323–331.
17.
Taylor, C. E. (1974). “Simplification of the analysis of stress in conical shells.” Theor. and Appl. Mech. Rep. No. 385, Univ. of Illinois, Urbana, Ill.
18.
Teng, J. G., and Rotter, J. M. (1988). “Plastic collapse of steel silo hoppers.” Res. Rep. R568, School of Civ. and Mining Engrg., Univ. of Sydney, Sydney, Australia, Apr.
19.
Timoshenko, S., and Woinowsky‐Krieger, S. (1959). Theory of plates and shells. McGraw‐Hill, New York, N.Y.
20.
Trahair, N. S., et al. (1983). “Structural design of steel bins for bulk solids.” Australian Inst. Steel Constr., Nov.
21.
Watts, G. W., and Burrows, W. R. (1969). “The basic elastic theory of vessel heads under internal pressure.” J. Appl. Mech., Trans. ASME, 71(Mar.),55–73.
Information & Authors
Information
Published In
Copyright
Copyright © 1990 ASCE.
History
Published online: Sep 1, 1990
Published in print: Sep 1990
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.