Destructive Testing of Metal‐Plate‐Connected Wood Truss Joints
Publication: Journal of Structural Engineering
Volume 116, Issue 7
Abstract
Load‐displacement characteristics and failure modes of metal‐plate‐connected wood truss joints are presented. Tension splice, heel, and web at the bottom chord joints are fabricated using southern pine (SP) no. 2 lumber and 20‐gage punched metal plates. These joints are tested with a newly developed testing appratus that allows the testing of all three joints without major modifications. In‐plane loads are applied to simulate the loads carried by truss members. The computerized testing apparatus and methods show potential as an efficient testing procedure to assess joint behavior. The average strength of tension splice, heel, and web at the lower chord joints is 27.0 kN, 22.7 kN, and 16.7 kN, respectively. The failure of the heel joint is characterized as ductile, and that of the tension splice and web at the bottom chord joints as brittle. The failure of the joints is a combination of wood and teeth failure. The results are useful for semirigid joint analysis and design of metal‐plate‐connected wood trusses.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Gupta, R., and Gebremedhin K. G. (1988). “An experimental investigation to determine the strength of tension splice joints.” Proc. 1988 Int. Conf. on Timber Engrg., R. Y. Itani, ed., Washington State Univ./Forest Products Res. Soc. 1, 257–265.
2.
Heard, L. R., Winistorfer, S. G., and Grossthanner, O. A. (1988). “Analysis of metal plate connected high capacity tension splices for wood trusses.” Proc. 1988 Int. Conf. on Timber Engrg., R. Y. Itani, ed., Washington State Univ./Forest Products Res. Soc., 2, 149–162.
3.
Lau, P. W. C. (1987). “Factors affecting the behavior and modelling of toothed metal‐plate joints.” Can. J. Civ. Engrg., 14(2), 183–195.
4.
Maragechi, K., and Itani, R. Y. (1984). “Influence of truss plate connectors on the analysis of light frame structures.” Wood and Fiber Sci., 16(3), 306–322.
5.
McLain, T. E. (1983). “Mechanical fastening of structural wood members—Design and research status.” Structural wood research state‐of‐the‐art and research needs, R. Y. Itani and K. F. Faherty, eds., ASCE/Nat. Sci. Found./Washington State Univ., 33–70.
6.
“Methods of test for evaluation of truss plate used in lumber joints.” (1980). Standard S347‐M1980, Can. Standards Assoc., Rexdale, Ontario, Canada.
7.
Misra, R. D., and Esmay, M. L. (1966). “Stress distribution in the punched metal plate of a timber joint.” Trans., Amer. Soc. of Agric. Engrs., 9(6), 839–842, 845.
8.
Quaile, A. T., and Keenan, F. J. (1979). “Truss plate testing in Canada: Test procedures and factors affecting strength properties.” Proc. of Metal Plate Wood Truss Conf., Forest Products Res. Soc., 105–112.
9.
Sheppard, I. (1969). “An analytical and experimental investigation of contact area stress distribution and buckling strength of light gage punched metal heel plates for timber trusses,” thesis presented to Michigan State University, at East Lansing, Mich., in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
10.
“Standard test methods for moisture content of wood.” (1974). ASTM D2016‐74, Amer. Soc. of Testing and Materials, Philadelphia, Pa., Vol. 04.09, 433–434.
11.
“Standard methods of testing mechanical fasteners in wood.” (1977). ASTM D1761‐77, Amer. Soc. of Testing and Materials, Philadelphia, Pa., Vol. 04.09, 417–418.
12.
“Standard test methods for specific gravity of wood and wood‐base materials. (1983). ASTM D2395‐83. Amer. Soc. of Testing and Materials, Philadelphia, Pa., 497–499.
13.
Suddarth, S. K., Percival, D. H., and Comus, Q. B. (1979). “Variability in tension performance of metal plate connections.” Proc. Metal Plate Wood Truss Conf., Forest Products Res. Soc., 98–104.
Information & Authors
Information
Published In
Copyright
Copyright © 1990 ASCE.
History
Published online: Jul 1, 1990
Published in print: Jul 1990
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.