Behavior of Isotropic R/C Bridge Decks on Steel Girders
Publication: Journal of Structural Engineering
Volume 116, Issue 3
Abstract
An experimental and analytical investigation is conducted regarding the behavior of Ontario‐type reinforced concrete bridge decks. A full‐scale bridge deck (both cast‐in‐place and precast), detailed in accordance with the Texas State Department of Highways provisions for Ontario‐type decks, and having about 60% of the reinforcement required by the current AASHTO code, performs well under current AASHTO design load levels. Under service and overload conditions (about three times the current AASHTO design wheel load), the behavior of the deck slab is essentially linear. Membrane forces do not noticeably affect the performance of the bridge prior to deck cracking. After cracking, significant compressive membrane forces are present in the deck, and could significantly increase its flexural capacity. Detailed finite element models of the specimen are developed for both the cast‐in‐place and precast panel deck cases. Cracking of the deck is followed using sequential linear analyses with a smeared cracking model. Analytical predictions agree well with experimental results.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Barker, J. M. (1975). “Research, adaptation and experience with precast prestressed deck panels.” PCI J., 20(6), 67–82.
2.
Barnoff, R. M., and Rainey, D. L. (1974). “Laboratory tests of prestressed concrete deck planks and deck plank assemblies.” Report No. 2, Pennsylvania Transportation Institute, Pennsylvania State University, University Park, Pa.
3.
Batchelor, B. deV., Hewitt, B. E., and Csagoly, P. (1978). “Investigation of the fatigue strength of deck slabs of composite steel/concrete bridges.” Transp. Res. Rec., 664, 153–161.
4.
Beal, D. B. (1981). “Strength of concrete bridge deck.” Research Report 89, New York Department of Transportation, Albany, N.Y.
5.
Bieschke, L. A., and Klingner, R. E. (1982). “The effect of transverse strand extensions on the behavior of precast prestressed panel bridges.” Research Report No. 303‐1F, Center for Transportation Research, University of Texas at Austin, Austin, Tex.
6.
Brotchie, J. F., and Holley, M. J. (1971). “Membrane action in slabs.” Special Publication SP‐30, Am. Concr. Inst., 345–377.
7.
Buth, E., Furr, H. L., Jones, H. L., and Toprac, A. A. (1972). “Evaluation of a prestressed panel, cast‐in‐place concrete bridge.” Research Report 145‐3, Texas Transportation Institute, Texas A & M University, College Station, Tex.
8.
Christiansen, K. P. (1982). “Experimental investigation of rectangular concrete slabs with horizontal restraints.” Mater. Struct., 16(93), 178–192.
9.
Csagoly, P., Holowka, M., and Dorton, R. A. (1978). “The true behavior of thin concrete bridge slabs.” Transp. Res. Rec., 664, 171–179.
10.
Dorton, R. A., and Holowka, M. (1977). “The Conestogo River bridge—Design and testing.” Can. J. Civ. Engrg., 4(1), 18–39.
11.
Elling, C. W., Klingner, R. E., and Burns, N. H. (1985). “Distribution of girder loads in a composite highway bridge.” Research Report 350‐2, Center for Transportation Research, University of Texas at Austin, Austin, Tex.
12.
Fang, I.‐K., Worley, J. A., Burns, N. H., and Klingner, R. E. (1986). “Behavior of Ontario‐type bridge decks on steel girders.” Research Report 350‐1, Center for Transportation Research, University of Texas at Austin, Austin, Tex.
13.
Furr, H. L., and Ingram, L. L. (1972). “Cyclic load tests of composite prestressed‐reinforced concrete panels.” Research Report 145‐4, Texas Transportation Institute, Texas A&M Univ., College Station, Tex.
14.
Girolami, A. G., Sozen, M. A., and Gamble, W. L. (1970). “Flexural strength of reinforced concrete slabs with externally applied in‐plane forces.” Report, Defense Office of the Secretary of the Army and Office of Civil Defense, Washington, D.C.
15.
Hewitt, B. E. (1972). “An investigation of the punching strength of restrained slabs with particular reference to the deck slabs of composite I‐beam bridges,” thesis presented to Queen's University, at Kingston, Ontario, Canada, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
16.
Hewitt, B. E., and Batchelor, B. deV. (1975). “Punching shear strength of restrained slabs.” Proc., ASCE, ST9, 1827–1853.
17.
Holowka, M. (1979). “Testing of a trapezoidal box girder bridge.” Structural Research Report RR221, Ontario Ministry of Transportation and Communications, Toronto, Ontario, Canada.
18.
Holowka, M., and Csagoly, P. (1980). “A composite prestressed concrete AASHTO girder bridge.” Research Report RR222, Ontario Ministry of Transportation and Communications, Toronto, Ontario, Canada.
19.
Hopkins, D. C., and Park, R. (1971). “Test on a reinforced concrete slab and beam floor designed with allowance for membrane action.” Special Publication SP‐30, Am. Concr. Inst., 223–250.
20.
Hopkins, D. C., and Park, R. (1971). “Cracking, deflection and ultimate load of concrete slab systems.” Special Publication SP‐30, Am. Concr. Inst., 223–250.
21.
Kluge, R. W., and Sawyer, H. A. (1975). “Interacting pretensioned concrete form panels for bridge decks.” PCI J., 20(3), 34–61.
22.
Leibenberg, A. C. (1966). “Arching action in concrete slabs.” National Building Research Institute, Council for Scientific and Industrial Research, Report 234, Johannesburg, South Africa.
23.
Ockleston, A. J. (1955). “Load tests on a three story concrete building in Johannesburg.” Struct. Engr., 33(10), 304–322.
24.
Ockleston, A. J. (1958). “Arching action in reinforced concrete slabs.” Struct. Engr., 36(6), 197–201.
25.
Ontario highway bridge design code. (1983). Ontario Ministry of Transportation and Communications, 2nd Ed., Toronto, Ontario, Canada.
26.
Park, R. (1964). “Ultimate strength of rectangular concrete slabs under short‐term uniform loading with edges restrained against lateral movement.” Proc. Inst. Civ. Engr., 28(6705), 125–145.
27.
Park, R. (1965). “The lateral stiffness and strength required to ensure membrane action at the ultimate load of a reinforced concrete slab‐and‐beam floor.” Mag. Concr. Res., 17(50), 29–38.
28.
Reed, R. L. (1978). “Application and design of prestressed deck panels.” Transp. Res. Rec., 665, 164–171.
29.
Standard specifications for highway bridges. (1983). American Association of State Highway and Transportation Officials, 13th Ed., Washington, D.C.
30.
“Summary report on investigation to determine feasibility of using in‐place precast prestressed form panels for highway bridge decks.” (1975). Texas Highway Department PCI J., 20(3), 62–67.
31.
Tong, P. Y., and Batchelor, B. deV. (1971). “Compressive membrane enhancement in two‐way bridge slabs.” Special Publication SP‐30, Am. Concr. Inst., 271–286.
32.
Tsui, C. K., Burns, N. H., and Klingner, R. E. (1986). “Behavior of Ontario‐type bridge deck on steel girders: Negative moment region and load capacity.” Research Report 350‐3, Center for Transportation Research, University of Texas at Austin, Austin, Tex.
Information & Authors
Information
Published In
Copyright
Copyright © 1990 ASCE.
History
Published online: Mar 1, 1990
Published in print: Mar 1990
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.