Wood Connections with Heavy Bolts and Steel Plates
Publication: Journal of Structural Engineering
Volume 116, Issue 11
Abstract
Due to some recent failures, the use of large‐diameter bolts in timber connections appears to be questionable. The design procedure used today is mostly based on research that was performed in 1932. This paper presents the results of a study that was conducted to examine current design practices for bolts of 1 and 1.5 in. (25 and 38 mm) diameter in the low ratio range, when the connection is loaded perpendicular to grain by steel side plates. In addition, bolt‐modification factors and specification design geometry are examined for multiple bolt connections. The results are evaluated by comparison to yield theory as well as current design criteria. The correlation with yield theory and the results of other researchers is good for 1 in. (25 mm) diameter bolts; the 1.5 in. (38 mm) bolts did not perform as well as expected. The findings indicate that the current bolt‐modification factors may be unconservative for six bolt connections. Additionally, 1.5 in. (38 mm) diameter bolts exhibit reduced normalized bearing strengths in the low range. The design values for the 1 in. (25 mm) diameter bolts appear to be conservative.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
ASCE Committee on Wood. (1986). “Structural wood research needs.” J. Struct. Engrg., 112(9), 2155–2165.
2.
Call, R. D., and Bjorhovde, R. (1988). “Bolted timber connections with steel side plates.” Civ. Engrg. Res. Rept. No. ST1, Univ. of Pittsburgh, Pittsburgh, Pa., Aug.
3.
Doyle, D. V., and Scholten, J. A. (1963). “Performance of bolted joints in Douglas fir.” Research Paper No. FPL 2, Forest Products Lab., Madison, Wis., May.
4.
Manual of steel construction. (1980). 8th Ed., Amer. Inst. of Steel Constr., Chicago, Ill.
5.
McLain, T. E., and Thangjitham, S. (1983). “Bolted wood‐joint yield model.” J. Struct. Engrg., ASCE, 109(8), 1820–1835.
6.
“Mechanical testing of steel products.” (1981a). ASTM Standard No. A370‐86a, Amer. Soc. for Testing and Matls., Philadelphia, Pa.
7.
“Mechanical fasteners in wood.” (1981b). ASTM Standard D1761‐77, Amer. Soc. for Testing and Matls., Philadelphia, Pa.
8.
National design specification for wood construction. (1986). National Forest Products Assoc., Washington, D.C.
9.
Soltis, L. A., Hubbard, F. K., and Wilkinson, T. L. (1986). “Bearing strength of bolted timber joints.” J. Struct. Engrg., ASCE, 112(9), 2141–2154.
10.
“Specific gravity of wood and wood‐base materials.” (1981). ASTM Standard No. D2395‐69, Amer. Soc. for Testing and Matls., Philadelphia, Pa.
11.
Soltis, L. A., and Wilkinson, T. L. (1987). “Bolted connection design.” General Tech. Rept. No. FPL‐GTR‐54, Forest Products Lab., Madison, Wis., Jul.
12.
Timber construction manual. (1985). 3rd Ed., Amer. Inst. of Timber Constr., John Wiley and Sons, New York, N.Y.
13.
Trayer, G. W. (1932). “The bearing strength of wood under bolts.” Tech. Bulletin No. 332, U.S. Dept. of Agric., Washington, D.C., Oct.
Information & Authors
Information
Published In
Copyright
Copyright © 1990 ASCE.
History
Published online: Nov 1, 1990
Published in print: Nov 1990
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.