Web Crippling Strength of Cold‐Formed Steel Beams
Publication: Journal of Structural Engineering
Volume 115, Issue 10
Abstract
The structural behavior of high‐strength cold‐formed steel beams subjected primarily to web crippling is investigated analytically and experimentally. Hat sections and I‐beams, formed from five different types of high‐strength sheet steels, are investigated under various loading conditions. In addition to the test data gathered in this phase of study, the experimental results obtained from the beam tests conducted at various companies are carefully evaluated. The evaluation indicates that the present available design criteria are not suitable for high‐strength materials with yield strengths exceeding 80 ksi (552 MPa). New design formulas are derived for different types of loading conditions on the basis of available test data with material yield strengths ranging from 30 to 165 ksi (207 to 1,138 MPa). These empirical equations distinguish between web crippling failure caused by overstressing (bearing failure) and web buckling. Interaction formulas are derived for sections under combined web crippling and bending moment. The newly proposed design equations are verified by test results.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Automotive steel design manual. (1986). Amer. Iron and Steel Inst., Washington, D.C.
2.
Guide for preliminary design of sheet steel automotive structural components. (1981). Amer. Iron and Steel Inst., Washington, D.C.
3.
Errera, S. J. (1982). “Automotive structural design using the AISI guide.” SAE Tech. Paper Series 820021, Soc. of Automotive Engrs., Warrendale, Pa.
4.
Hetrakul, N., and Yu, W. W. (1978). “Structural behavior of beam webs subjected to web crippling and a combination of web crippling and bending.” Final Report, Civ. Engrg. Study 78‐4, Univ. of Missouri‐Rolla, June, Rolla, Mo.
5.
Khan, M. Z., and Walker, A. C. (1972). “Buckling of plates subjected to localized edge loading.” The Struct. Engr., 50(June).
6.
Khan, M. Z., Johns, K. C., and Hayman, B. (1977). “Buckling of plates with partially loaded edges.” J. Struct. Div., ASCE, 103(3), 547–558.
7.
Levy, B. S. (1983). “Advances in designing ultra high strength steel bumper reinforcement beams.” SAE Tech. Paper Series 830399, Soc. of Automotive Engrs., Warrendale, Pa.
8.
Lin, S. H. (1984). “Structural behavior of cold‐formed steel beam webs subjected to partial edge loading.” Thesis presented to the University of Missouri‐Rolla, at Rolla, Mo., in partial fulfillment of the requirements for the degree of Master of Science.
9.
Santaputra, C., Parks, M. B., and Yu, W. W. (1986). “Web crippling of cold‐formed steel beams using high strength sheet steels.” SAE Tech. Paper Series 860823, Soc. of Automotive Engrs., Warrendale, Pa.
10.
Santaputra, C. (1986). “Web crippling of high strength cold‐formed steel beams.” Thesis presented to the University of Missouri‐Rolla, at Rolla, Mo., in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
11.
Santaputra, C., and Yu, W. W. (1986). “Design of automotive structural components using high strength sheet steels: Web crippling of high strength cold‐formed steel beams.” Eighth Progress Report, Civ. Engrg. Study 86‐1, Univ. of Missouri‐Rolla, Rolla, Mo., Aug.
12.
Specification for the design of cold‐formed steel structural members. (1986). Amer. Iron and Steel Inst., Washington, D.C.
13.
Steel meets the automotive engineering challenges. (1983). Distributed at the 1983 SAE Exposition, Amer. Iron and Steel Inst., Washington, D.C.
14.
Vecchio, M. T. (1983). “Design analysis and behavior of a variety of as‐formed mild and high strength sheet materials in large deflection bending.” SAE Tech. Paper Series 830398, Soc. of Automotive Engrs., Warrendale, Pa.
15.
Yu, W. W., Santaputra, C., and Parks, M. B. (1983). “Design of automotive structural components using high strength sheet steels.” First Progress Report, Civil Engineering Study 83‐1, Univ. of Missouri‐Rolla, Rolla, Mo., Jan.
16.
Yu, W. W. (1985). Cold‐formed steel design. John Wiley & Sons, New York, N.Y.
Information & Authors
Information
Published In
Copyright
Copyright © 1989 ASCE.
History
Published online: Oct 1, 1989
Published in print: Oct 1989
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.