Preuplift Method to “Anchor” Liquid Storage Tanks
Publication: Journal of Structural Engineering
Volume 114, Issue 2
Abstract
Steel tanks for liquid storage often consist of a cylindrical shell attached to a steel bottom plate which rests on the ground. In many cases neither the bottom plate nor the cylindrical shell are fixed to the ground. When such an unanchored tank is subjected to seismic ground shaking, the lateral inertia of the contained liquid contributes to the overturning moment, but its weight cannot contribute to the stabilizing moment until some uplift of the bottom plate occurs. The hold‐down force, due to the weight of liquid resting on the uplifted portion of the bottom plate, provides the necessary resistance against overturning. However, this benefit of uplift comes at the cost of very high vertical compressive stresses in the tank wall at the base in the region diametrically opposite to where the maximum uplift occurs. The benefits of uplift can be reaped without some of its detrimental effects if the tank wall is preuplifted all around the circumference by means of a ring filler. An annular portion of the base plate is also preuplifted, but is not supported by the ring filler. The weight of liquid resting on that preuplifted portion of the base plate then becomes effective in resisting the overturning moment. For a 127 mm diameter Mylar tank, it is shown by experiment and analysis that preuplift increases the lateral load capacity by a factor of up to 2.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Water Works Association standard for welded steel tanks for water storage. (1984). ANSI/AWWA D100‐84, American Water Works Association, Denver, Colorado.
2.
Babcock, C. D. (1974). “Experiments in shell buckling.” Thin Shell Structures, Fung, Y. C. and Sechler, E. E., eds., 345–369, Prentice Hall.
3.
Clough, D. P. (1977). “Experimental evaluation of seismic design methods for broad cylindrical tanks.” Univ. of Calif., Berkeley, EERC Report UCB/EERC‐77/10, May.
4.
Clough, R. W. and Niwa, A. (1979). “Static tilt tests of a tall cylindrical liquid storage tank.” Earthquake Engineering Research Center, University of California, Berkeley, Report No. UCB/EERC, 79‐06, Feb.
5.
Hanson, R. D. (1973). “Behavior of liquid storage tanks.” The Great Alaska Earthquake of 1964, Engineering, National Academy of Sciences, Washington, D.C., 331–339.
6.
Jennings, P. C. (1971). “Engineering features of the San Fernando Earthquake, February 9, 1971.” Report No. EERL 71‐02, Earthquake Engrg. Res. Lab., Pasadena, Calif., Jun.
7.
Manos, G. C. and Clough, R. W. (1982). “Further study of the earthquake response of a broad cylindrical liquid‐storage tank model.” Report No. UCB/EERC‐82/07, Earthquake Engrg. Res. Center, Univ. of Calif., Berkeley, CA, My.
8.
Niwa, A. (1978). “Seismic behavior of tall liquid storage tanks.” Earthquake Engrg. Res. Center, Univ. of Calif., Berkeley, CA, Report No. UCB/EERC‐78/04, Feb.
9.
Niwa, A., and Clough, R. W. (1982). “Buckling of cylindrical liquid storage tanks under earthquake loading.” Earthquake Engineering and structural dynamics, 10, 107–122.
10.
Peek, R. (1986). “Analysis of unanchored liquid storage tanks under seismic loads.” Report No. EERL 86‐01, California Institute of Technology, Pasadena, California.
11.
Peek, R. and Jennings, P. C. (1987). “Simplified analysis of unanchored liquid storage tanks.” submitted to Earthquake Engineering and Structural Dynamics.
12.
Peek, R. (1987). “Analysis of unanchored liquid storage tanks under seismic lateral loads.” submitted to Earthquake Engrg. and Struct. Dynamics.
13.
Shibata, H., and Akiyama, H. (1985). “Seismic capacity testing of a thin wall 500 ton cylindrical tank.” Bulletin of the Earthquake Resistant Structure Research Center, 18, Institute of Industrial Science, University of Tokyo, March.
14.
Shih, C. F. (1981). “Failure of liquid storage tanks due to earthquake excitation.” Earthquake Engineering Research Laboratory, California Institute of Technology, Report No. EERL 81‐04, May.
15.
Timoshenko, S. and Woinowsky‐Krieger, S. (1959). Theory of plates and shells. 2nd Ed., McGraw‐Hill, New York, NY, 466–471.
16.
Weingarten, V. I., Morgan, E. J. and Seide, P. (1960). “Final report on development of design criteria for elastic stability of thin shell structures.” STL/TR‐60‐0000‐19425, Space Technology Laboratories, Inc., Los Angeles, California.
17.
“Welded tanks for oil storage.” (1979). American Petroleum Institute, Appendix E, API Standard 650, 6th Ed., Rev. 3.
18.
Wozniak, R. S. and Mitchell, W. W. (1978). “Basis of seismic design provisions for welded oil storage tanks.” Advances in Storage Tank Design, API, 43rd Midyear Meeting, Toronto, Ontario, Canada, May.
Information & Authors
Information
Published In
Copyright
Copyright © 1988 ASCE.
History
Published online: Feb 1, 1988
Published in print: Feb 1988
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.