Flexural Tensile Strength of Concrete Block Masonry
Publication: Journal of Structural Engineering
Volume 114, Issue 1
Abstract
This paper reports the results of 172 flexural tests of 790 mm by 1,590 mm () concrete block masonry walls. In addition to evaluating tensile strength both normal and parallel to the bed joint, the parameters included in the study are three sizes of block; three percentages of solid; four block strengths; two types of mortar; hollow blocks and ones grouted with three strengths of grout; and special conditions such as stack pattern, partial grouting, and empty head joints. The results confirm the orthotropic nature of masonry where for hollow blockwork, tensile strength parallel to the bed joint is two to four times higher than tensile strength normal to the bed joint. Grouting of the blockwork resulted in a greater increase of strength for tension normal to the bed joint so that these ratios are between 1 and 1.5. While the percent solid of the block has a marked influence, the tensile strength is not found to be significantly influenced by block size or block strength for the range tested. Grout strength is found to have little influence, particularly for tension normal to the bed joint. Comparison of the test values with allowable stresses recently adopted in North American building codes tends to raise questions regarding the justification for the allowable stresses for tension normal to the bed joints. Conversely, the practice of equating grout‐filled hollow masonry to solid masonry tends to ignore the very large benefits derived from the continuity provided by the continuous columns of grout. A general discussion of behavior and design concludes this paper.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Anderson, C. (1976). “Lateral loading tests on concrete block walls.” The Struct. Engr., 54(7), 239–246.
2.
Building code requirements for concrete masonry structures. (1983). American Concrete Institute Committee 531, ACI 531‐83, Detroit, Mich.
3.
Code of practice for structural use of masonry, part 1, unreinforced masonry. (1978). BS5628: Part 1, London, England.
4.
Cajdert, A. (1980). “Laterally loaded masonry walls.” Chalmers University of Technology, Division of Concrete Structures, Publication 80:5, Goteborg, Sweden.
5.
deVeckey, R. C., and West, H. W. H. (1980). “The flexural strength of concrete blockwork.” Magazine of Concrete Res., 32(113), 206–218.
6.
Drysdale, R. G., Hamid, A. A., and Heidebrechy, A. C. (1979). “Tensile strength of concrete and masonry.” J. Struct. Div., ASCE, 105(7), 1261–1276.
7.
Essawy, A., and Drysdale, R. G. (1983). “Capacity of block masonry under uniformly distributed loading normal to the surface of the wall.” Proc. 3rd Canadian Masonry Symposium, Edmonton, Alberta, Canada, 39‐1–39‐16.
8.
Gairns, D. A. (1983). “Flexural behaviour of concrete blockwork panels,” thesis presented to the University of Melbourne, at Melbourne, Australia, in partial fulfillment of the requirements for the degree of Master of Science.
9.
Gazzola, E., et al. (1985). “Influence of mortar materials on the flexural tensile bond strength of block and brick masonry.” Masonry: Research, Applications and Problems, ASTM STP871, ASTM, Philadelphia, Pa., 17–28.
10.
Masonry design for buildings. (1984). Canadian Standards Association, CAN 3‐S304‐M84, Rexdale, Ontario.
11.
SAA blockwork code, Part 1: Unreinforced blockwork. (1977). Standards Association of Australia, AS 1475, Part 1, North Sydney, New South Wales, Australia.
12.
Uniform building code. (1985), “Masonry codes and specifications.” International Conference on Building Officials, Whittier, Calif.
Information & Authors
Information
Published In
Copyright
Copyright © 1988 ASCE.
History
Published online: Jan 1, 1988
Published in print: Jan 1988
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.