Simplified Design of Unstiffened and Stiffened Plates
Publication: Journal of Structural Engineering
Volume 113, Issue 10
Abstract
Based on a reevaluation of 490 tests by different researchers, simple design formulas for the ultimate strength of unstiffened and stiffened steel plates under in‐plane compression without or with lateral loads are presented. These formulas take advantage of the empirical formulation of column‐type curves that allow the consideration of all relevant parameters (e.g., plate slenderness, column slenderness, and stitfener slenderness) and three grades (low, average, and high) of geometric imperfections and residual welding stresses. It is not necessary to introduce effective plate widths. The influence of lateral loads is covered by an interaction formula.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Aalami, B., Moukhtarzade, A., and Mahmudi‐Saati, P., “On the Strength Design of Ship Plates Subjected to In‐Plane and Transverse Loading,” Transactions, RINA, Vol. 114, 1972, pp. 519–534.
2.
Andrä, W., Beyer, E., and Wintergerst, L., “Beulversuche mit Bodenblechen von stählernen Hohlkästen,” Bauingenieur, Vol. 49, No. 10, Oct., 1974, pp. 373–382;
Discussion, Vol. 50, 1975, pp. 441–442.
3.
Barbré, R., Grassl, H., Schmidt, H., and Kruppe, J., Traglastversuche an Ausschnitten gedrückter Gurte mehrerer Hohlkastenbrücken, Institut für Stahlbau, Technische, Universität Braunschweig, Braunschweig, West Germany, 1976.
4.
Barbré, R., Schmidt, H., and Riemann, S., “Traglastversuche an längsgestäuchten, durch Wulstflachstähle versteiften Blechen mit freien Längsrändern,” Stahlbau, Vol. 51, No. 11, Nov., 1982, pp. 321–332.
5.
Becker, H., “Instability Strength of Polyaxially Loaded Plates and Relation to Design,” Steel Plated Structures, Vol. 1, Crosby Lockwood and Staples, London, U.K., 1977, pp. 559–580.
6.
Box, T., “A Practical Treatise on the Strength of Materials,” Spon, London, England, 1883.
7.
Clarkson, J., “Tests of Flat Plated Ship Grillages under Uniform Pressure,” Transactions, RINA, Vol. 105, 1963, pp. 467–484.
8.
Dibley, J. E., and Manoharan, A., “Experimental Behaviour of Two‐Span Continuous Box Girders,” Proceedings International Conference on Steel Box Girder Bridges, ICE, London, U.K., 1973, pp. 119–130.
9.
Dorman, A. P., and Dwight, J. B., “Tests on Stiffened Compression Panels and Plate Panels,” Proceedings International Conference on Steel Box Girder Bridges, ICE, London, U.K., 1973, pp. 63–75.
10.
Dowling, P. J., Chatterjee, S., Frieze, P. A., and Moolani, F. M., “Experimental and Predicted Behaviour of Rectangular Steel Box Girders,” Proceedings International Conference on Steel Box Girder Bridges, ICE, London, U.K., 1973, pp. 77–94.
11.
Dubas, P., “Essais sur le comportement post‐critique de poutres en caisson raidies,” Proceedings, IABSE Seminary, London, U.K., 1971, pp. 367–379.
12.
Dubas, P., “Plated Structures with Closed‐Section Stiffeners,” Steel Plated Structures, Vol. 1, Crosby, Lockwood and Staples, London, U.K., 1977, pp. 265–283.
13.
Dubas, P., “Ultimate Strength of Compression Members with Intermittent Rigid or Flexible Lateral Supports,” Second International Colloquium on Stability of Steel Structures, Preliminary Report, Liegé, Belgium, 1977, pp. 469–477.
14.
Dwight, J. B., and Little, G. H., “Stiffened Steel Compression Flanges—A Simpler Approach,” Structural Engineer (London), Vol. 54, No. 12, Dec., 1976, pp. 501–509.
15.
Dwight, J. B., and Moxham, K. E., “Welded Steel Plates in Compression,” Structural Engineer, (London), Vol. 47, No. 2, Feb., 1969, pp. 49–66.
16.
Engesser, F., “Zusatzkräfte und Nebenspannungen eisemer Fachwerkbrücken,” Vol. 2, Springer, Berlin, Germany, 1892, p. 151.
17.
Fischer, M., and Harre, W., “Ermittlung der Traglastkurven von einachsig gedrückten Rechteckplatten aus Baustahl der Seitenverhältnisse Hilfe von Versuchen,” Stahlbau, Vol. 47, No. 7, (1978), pp. 199–204,
and No. 8, pp. 239–247.
18.
Fukumoto, Y., Usami, T., and Okamoto, Y., “Ultimate Strength of Stiffened Plates,” Proceedings ASCE Specialty Conference on Metal Bridges, St. Louis, Mo., 1974, pp. 201–230.
19.
Heckel, R., “Der Schadensfall und die Wiederinstandstellung der vierten Donaubrucke in Wien,” Osterreichische Ingenieur‐Zeitschrift, Vol. 116, No. 10, 1971, pp. 301–307.
20.
Herzog, M. A. M., “Die Durchbiegung orthotroper Fahrbahnplatten aus Baustahl bis zum Bruch,” Bauingenieur, Vol. 48, No. 8, 1973, pp. 286–289.
21.
Herzog, M. A. M., “Die Traglast versteifter Kastenträger aus Baustahl,” Bauingenieur Vol. 52, No. 2, 1977, pp. 57–61.
22.
Herzog, M. A. M., “Einfache Näherungsformeln zur Bemessung unversteifter und versteifter Bleche unter Axialdruck, Schub und Querbelastung,” Schiffstechnik, Vol. 34, No. 2, 1987.
23.
Herzog, M. A. M., “Simple Design Formulas for Unstiffened and Stiffened Plates in Uniaxial Compression,” Proceedings, International Conference on Steel and Aluminium Structures, Vol. 1, Cardiff, U.K., 1987 (in press).
24.
Horne, M. R., Montague, P., and Narayanan, R., “Influence on Strength of Compression Panels of Stiffener Section, Spacing and Welded Connections,” Proceedings ICE, Part 2, Vol. 63, No. 1, 1977, pp. 1–20.
25.
Horne, M. R., and Narayanan, R., “An Approximate Method for the Design of Stiffened Steel Compression Panels,” Proceedings, ICE (London), Part 2, Vol. 59, No. 3, 1975, pp. 501–514.
26.
Horne, M. R., and Narayanan, R., “Ultimate Capacity of Longitudinally Stiffened Plates Used in Box Girders,” Proceedings, ICE, Part 2, Vol. 61, No. 2, 1976, pp. 253–280.
27.
Kell, C. O., “Investigation of Structural Characteristics of Destroyers ‘Preston’ and ‘Bruce’,” Transactions SNAME, Vol. 39, 1931, pp. 35–62,
and Vol. 48, 1940, pp. 125–172.
28.
Klöppel, K., Schmied, R., and Schubert, J., “Die Traglast mittig und ausmittig gedrückter Stützen mit kastenförmigem Querschnitt imüberkritischen Bereich unter Verwendung der nichtlinearen Beultheorie,” Stahlbau Vol. 35, No. 11, 1966, pp. 321–337,
and Vol. 38, No. 1, 1969, pp. 9–19,
and No. 3, 73–83.
29.
Kondo, J., and Ostapenko, A., “Tests on Longitudinally Stiffened Plate Panels with Fixed Ends,” Fritz Engineering Laboratory Report 248.12, Lehigh University, Bethlehem, Pa., 1964.
30.
Lang, D. W., and Warren, W. G., “Structural Strength Investigations on Destroyer ‘Albuera’,” Transactions INA, Vol. 94, No. 4, 1952, pp. 243–286.
31.
Maquoi, R., and Massonnet, C., “Théorie non‐linéaire de la résistance post‐critique des grandes poutres en caisson raidies,” IABSE Proceedings, Zurich, Switzerland, Vol. 31/II, 1971, pp. 91–140.
32.
Maquoi, R., and Massonnet, C., “Vérification expérimentale de la résistance postcritique des semelles comprimées raidies sur six poutres en caisson,” IABSE Proceedings, Vol. 36/I, 1976, pp. 159–187.
33.
Murray, N. W., “The Behaviour of Thin Stiffened Steel Plates,” IABSE Proceedings Vol. 33/I, 1973, pp. 191–201.
34.
Murray, N. W., “Buckling of Stiffened Panels Loaded Axially and in Bending,” Structural Engineer (London), Vol. 51, No. 7, 1973, pp. 285–301.
35.
Murray, N. W., “Das Stabilitätsverhalten von axial belasteten, in Langsrichtung ausgesteiften Flatten im plastischen Bereich,” Stahlbau, Vol. 42, No. 12, 1973, pp. 372–379.
36.
Murray, N. W., “Introduction to the Theory of Thin‐Walled Structures,” Clarendon Press, Oxford, England, 1984.
37.
Ostapenko, A., and Lee, T. T., “Tests on Longitudinally Stiffened Plate Panels Subjected to Lateral and Axial Loading,” Fritz Engineering Laboratory Report 248.4, Lehigh University, Bethlehem, Pa., 1960.
38.
Rampetsreiter, R. H., Lee, T. T., and Ostapenko, A., “Tests on Longitudinally Stiffened Plate Panels—Effect of Residual Stresses and Rotational Restraint by Stiffeners,” Fritz Engineering Laboratory Report 248.5, Lehigh University, Bethlehem, Pa., 1962.
39.
Roik, K. H., Kindmann, R., and Schaumann, P., “Plattenbeulversuche—8 Grossversuche mit langs‐und querausgesteiften Blechfeldern,” DAST‐Berichte No. 12, Stahlbau‐Verlag, Cologne, West Germany, 1982.
40.
Rouvé, B., “Calcul du comportement postcritique des plaques raidies par la méthode des eléménts finis,” Report 76‐1, Chair of Applied Statics and Steel Structures, Federal Institute of Technology, Zurich, Switzerland, 1976.
41.
Sawczuk, A., and Jaeger, T., “Grenztragfahigkeits‐Theorie der Platten,” Springer, Berlin, West Germany, 1963.
42.
Scheer, J., and Vayas, J., “Traglastversuche an längsgestauchten, versteiften Rechteckplatten mit allseitiger Lagerung,” Stahlbau Vol. 52, No. 3, 1983, pp. 78–84.
43.
Scheer, J., and Vayas, J., “Traglastversuche an längsgestauchten und schubbeanspruchten, versteiften Rechteckplatten,” Stahlbau, Vol. 52, No. 7, 1983, pp. 207–213.
44.
Scheer, J., and Grüter, A., “Traglastversuche an längsgestauchten, mit trapezförmigen Hohlrippen versteiften Rechteckplatten mit freien Längsrändern,” Stahlbau Vol. 53, No. 9, 1984, pp. 275–280.
45.
Schmidt, H., and Clausnitzer, W., “Plastisches Beulverhalten axial gedrückter Trapezhohlsteifen,” Stahlbau Vol. 53, No. 1, 1984, pp. 7–12.
46.
Smith, C. S., “Compressive Strength of Welded Steel Ship Grillages,” Transactions RINA, Vol. 117, 1975, pp. 325–359.
47.
Usami, T., and Fukumoto, Y., “Local and Overall Buckling of Welded Box Columns,” Journal of Structural Division, ASCE, Vol. 108, 1982, No. ST3, March, 1982, pp. 525–542.
48.
Usami, T., and Fukumoto, Y., “Welded Box Compression Members,” Journal of Structural Engineering, ASCE, Vol. 110, No. ST10, Oct., 1984, pp. 2457–2470.
49.
Yoshiki, M., and Fujita, Y., “On the Ultimate Strength of Stiffened Plates Subjected to Compression Load,” Naval Architecture & Shipbuilding in Japan, (Tokyo), Vol. 104, 1958, pp. 149–155.
Information & Authors
Information
Published In
Copyright
Copyright © 1987 ASCE.
History
Published online: Oct 1, 1987
Published in print: Oct 1987
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.