Sensitivity Study of Optimum RC Restrained End T‐Sections
Publication: Journal of Structural Engineering
Volume 112, Issue 8
Abstract
Economical restrained end reinforced concrete T‐sections are established using an optimization routine and the strength design procedure. The objective function includes the in‐place cost of formwork, concrete, longitudinal reinforcement, stirrup reinforcement, and depth‐related costs. The continuous function design variables are the beam stem width, effective depth, areas of tension and compression reinforcement, and percentages of support moment redistribution. Linear and nonlinear continuous functions are applied to establish side and behavorial constraints. The behavorial constraints include the nominal moment and shear strengths at critical locations and deflection limitations. Comparisons of optimum beam designs, obtained by changing a particular design parameter, are made to indicate design sensitivity. These parameter studies show the individual effects of allowable deflection, material strengths, support continuity, and unit material cost variation. The paper concludes with guidelines for economical T‐sections that are based on the results of the parameter sensitivity studies.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Abendroth, R. E., “Optimum Design for Reinforced Concrete Beams,” thesis presented to the University of Wisconsin, at Madision, Wis., in 1983, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
2.
Abendroth, R. E., and Salmon, C. G., “Sensitivity Study of Reinforced Concrete Simple Beams,” ISU‐ERI‐Ames‐86402, Iowa State Univ., Engineering Research Institute, June, 1985.
3.
Anand, Y. N., et al., Discussion of “Optimum Singly Reinforced Concrete Sections,” by L. L. Friel, Journal of the American Concrete Institute, Vol. 72, No. 5, May, 1975, pp. 249–253.
4.
Baker, J. C., et al., Discussion of “Economical Design of Reinforced Concrete Slabs Using Ultimate Strength Theory,” by E. Traum, Journal of the American Concrete Institute, Vol. 60, No. 12, Dec., 1963, pp. 1893–1900.
5.
Brown, R. H., “Minimum Cost Selection of One‐Way Slab Thickness,” Journal of the Structural Division, ASCE, Vol. 101, No. ST12, Paper No. 11785, Dec., 1975, pp. 2585–2590.
6.
Brown, R. H., Closure of “Minimum Cost Selection of One‐Way Slab Thickness,” Journal of the Structural Division, ASCE, Vol. 103, No. ST10, Oct., 1977, pp. 2065–2066.
7.
Broyden, C. G., “Quasi‐Newton Methods and Their Application to Function Minimization,” Mathematics of Computation, Vol. 21, 1967, pp. 368–380.
8.
Building Code Requirements for Reinforced Concrete, ACI Std. 318‐83, American Concrete Institute, Detroit, Mich., 1983.
9.
Building Construction Cost Data 1977, 35th annual ed., Robert Snow Means Company, Inc., Construction Consultants & Publishers, Duxbury, Mass., 1976.
10.
Chou, T., “Optimum Reinforced Concrete T‐Beam Sections,” Journal of the Structural Division, ASCE, Vol. 103, No. ST8, Aug., 1977, pp. 1605–1617.
11.
Cohn, M. Z., “Optimum Limit Design for Reinforced Concrete Continuous Beams,” Proceedings of the Institute of Civil Engineers, Proc. Paper No. 6680, Apr., 1965, pp. 675–707.
12.
Cohn, M. Z., and Grierson, D. E., “Optimum Design of Reinforced Concrete Beams and Frames,” Final Publications, Eighth Congress of the International Association for Bridge and Structural Engineering, Sept., 1968, pp. 215–225.
13.
Cohn, M. Z., and MacRae, A. J., “Optimization of Structural Concrete Beams,” Journal of the Structural Division, ASCE, Vol. 110, No. ST7, July, 1984, pp. 1573–1588.
14.
Fletcher, R., and Powell, M. J. D., “A Rapidly Convergent Descent Method for Minimization,” Computer Journal, Vol. 6, No. 2, 1963, pp. 163–168.
15.
Fox, R. L., Optimization Methods for Engineering Design, Addison‐Wesley Publishing Company, Reading, Mass., 1971.
16.
Friel, L. L., “Optimum Singly Reinforced Concrete Sections,” Journal of the American Concrete Institute, Vol. 71, No. 11, Nov., 1974, pp. 556–558.
17.
Gustafson, D. P., and Thakkar, M. C., Discussion of “Minimum Cost Selection of One‐Way Slab Thickness,” Journal of the Structural Division, ASCE, Vol. 102, No. ST10, Oct., 1976, pp. 2093–2095.
18.
Hill, L. A., Jr., “Automated Optimum Cost Building Design,” Journal of the Structural Division, ASCE, Vol. 92, No. ST12, Dec., 1966, pp. 247–263.
19.
Kaliszky, S., “On the Optimum Design for Reinforced Concrete Structures,” Acta Technica Academiae Scientiarum Hungaricae, Tom. LX, Fasc. 3–4, 1968, pp. 257–264.
20.
Kirsch, Uri, Optimum Structural Design, McGraw‐Hill Book Co., N.Y., 1981.
21.
Martin, I., Discussion of “Minimum Cost Selection of One‐Way Slab Thickness,” by R. H. Brown, Journal of the Structural Division, ASCE, Vol. 102, No. ST7, July, 1976, p. 1529.
22.
Naaman, A. E., and Srinivasan, C. N., Discussion of “Minimum Cost Selection of One‐Way Slab Thickness,” by R. H. Brown, Journal of the Structural Division, ASCE, Vol. 102, No. ST9, Sept., 1976, pp. 1959–1964.
23.
Norman, D. G., “Economic Aspects in the Design of Some Reinforced Concrete Structural Members,” Journal of the American Concrete Institute, Vol. 61, No. 4, Apr., 1964, pp. 310–440.
24.
Petcu, V., “Optimum Plastic Moments of Reinforced Concrete Continuous Beams,” The Indian Concrete Journal, Vol. 36, No. 3, Mar., 1962, pp. 110–113.
25.
Rajagopalan, K., and Subrahmanyam, B. V., Discussion of “Minimum Cost Selection of One‐Way Slab Thickness,” by R. H. Brown, Journal of the Structural Division, ASCE, Vol. 103, No. ST12, Dec., 1976, pp. 2378–2382.
26.
Rao, P. S., and Krishnamoorthy, C. S., “Cost Comparison of Reinforced Concrete Flexural Members Designed by the Ultimate Load and the Working Stress Methods as Specified in IS:456:1964,” The Indian Concrete Journal, Feb., 1970, pp. 61–66, 82.
27.
Sawyer, H. A., “Economy and Concrete Beams,” Journal of the American Concrete Institute, Vol. 48, No. 9, May, 1952, pp. 773–784.
28.
Stanley, J. R., and Creasy, L. R., Discussion on “Economics of Framed Structures,” Proceedings of the Institute of Civil Engineers, Vol. 14, Sept.–Dec., 1959, pp. 438–439 and 445.
29.
Traum, E., “Economical Design of Reinforced Concrete Slabs Using Ultimate Strength Theory,” Journal of the American Concrete Institute, Vol. 60, No. 6, June, 1963, pp. 763–773.
Information & Authors
Information
Published In
Copyright
Copyright © 1986 ASCE.
History
Published online: Aug 1, 1986
Published in print: Aug 1986
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.