Cyclic In‐Plane Buckling of Double Angle Bracing
Publication: Journal of Structural Engineering
Volume 110, Issue 9
Abstract
The behavior of double‐angle bracing members subjected to in‐plane buckling due to severe cyclic load reversals is investigated. Eight full‐size test specimens made of back‐to‐back double angle sections, connected to the end gusset plates by fillet welds or high strength bolts, were tested under large amplitude cyclic loading. Some test specimens, designed by current code procedures showed failures during early cycles of loading. Based on the observations and analysis of the behavior of test specimens new design procedures are proposed to improve the ductility and energy dissipation capacity of double angle bracing members and their connections to withstand severe cyclic loadings.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Astaneh‐Asl, A., Goel, S. C., and Hanson, R. D., “Cyclic Behavior of Double Angle Bracing Members with End Gusset Plates,” Report No. UMEE82R7, Department of Civil Engineering, The University of Michigan, Ann Arbor, Mich., Aug., 1982.
2.
Black, R. G., Wenger, W. A., and Popov, E. P., “Inelastic Buckling of Steel Struts Under Cyclic Load Reversals,” Report No. UBS/EERC‐80/40, Univ. of California, Berkeley, Calif., Oct., 1980.
3.
Blodgett, O. W., “Design of Welded Structures,” J. F. Lincoln Arc Welding Foundation, Cleveland, Ohio, 1966, pp. 5.9–27.
4.
Fisher, J. W., and Sturik, J. H. A., “Guide to Design Criteria for Bolted and Riveted Joints,” John Wiley & Sons, New York, N.Y., 1974, pp. 241–249.
5.
Ghanaat, Y., “Study of X‐Braced Steel Frame Structures Under Earthquake Simulation,” Report No. UBC/EERC‐80/08, Univ. of California, Berkeley, Calif., 1980.
6.
Gugerli, H., and Goel, S. C., “Inelastic Cyclic Behavior of Steel Bracing Members,” Report No. UMEE 82R1, Department of Civil Engineering, The Univ. of Michigan, Ann Arbor, Mich., Jan., 1982.
7.
Higginbotham, A. B., and Hanson, R. D., “Axial Hysteretic Behavior of Steel Members,” Journal of the Structural Division, ASCE, Vol. 102, No. ST7, July, 1976.
8.
Irvan, W. G., Jr., “Experimental Study of Primary Stresses in Gusset Plates of a Double Plane Pratt Truss,” Univ. of Kentucky Engineering Experiment Station Bulletin, No. 46, Dec., 1957.
9.
Jain, A. K., and Goel, S. C., “Hysteresis Models for Steel Members Subjected to Cyclic Buckling or Cyclic End Moments and Buckling,” Report No. UMEE 78R6, Department of Civil Engineering, The Univ. of Michigan, Ann Arbor, Mich., Dec., 1978.
10.
Jain, A. K., Goel, S. C., and Hanson, R. D., “Hysteresis Behavior of Bracing Members and Seismic Response of Braced Frames with Different Proportions,” Report No. UMEE 78R3, Department of Civil Engineering, Univ. of Michigan, Ann Arbor, Mich., July, 1978.
11.
Kahn, L. F., and Hanson, R. D., “Inelastic Cycles of Axially Loaded Steel Members,” Journal of the Structural Division, ASCE, Vol. 102, No. ST5, Proc. Paper 12111, May, 1976.
12.
Manual of Steel Construction, 8th ed., American Institute of Steel Construction, Chicago, Ill., 1980.
13.
Nilforoushan, R., “Seismic Behavior of Multistory K‐Braced Frame Structures,” thesis presented to the Univ. of Michigan, at Ann Arbor, Mich., in 1973, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
14.
Nonaka, T., “An Elastic‐Perfectly Plastic Analysis of a Bar Under Repeated Loading,” International Journal of Solids and Structures, Vol. 9, No. 5, 1973, pp. 569–580.
15.
Popov, E. P., “Inelastic Behavior of Steel Braces Under Cyclic Loading,” Proceedings, Second U.S. National Conference on Earthquake Engineering, Stanford University, Stanford, California, Aug. 22–24, 1979, pp. 923–932.
16.
Popov, E. P., Takanashi, K., and Roeder, C. W., “Structural Steel Bracing Systems: Behavior Under Cyclic Loading,” Report No. UBC/EERC‐76/17, Univ. of California, Berkeley, Calif., 1976.
17.
Roeder, C. W., and Popov, E. P., “Eccentrically Braced Steel Frames for Earthquakes,” Journal of the Structural Division, ASCE, Vol. 104, No. ST3, Proc. Paper 13619, Mar., 1978, pp. 391–412.
18.
Sheridan, M. L., “An Experimental Study of the Stress and Strain Distribution in Steel Gusset Plates,” presented to the University of Michigan, in 1953, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
19.
Shibata, M., Nakamura, T., Yoshida, N., Morino, S., Nonaka, T., and Wakabayashi, M., “Elasto‐Plastic Behavior of Steel Braces Under Repeated Axial Loading,” Proceedings V World Conference on Earthquake Engineering, Rome, Italy, 1973, pp. 845–848.
20.
Singh, P., “Seismic Behavior of Braces and Braced Steel Frames,” Report No. UMEE 77R1, Civil Engineering Department, The Univ. of Michigan, Ann Arbor, Mich., July, 1977.
21.
Specification for the Design, Fabrication and Errection of Structural Steel for Buildings, American Institute of Steel Construction, 1978.
22.
Uniform Building Code, International Conference of Building Officials, Whittier, Calif., 1982, p. 137.
23.
Walker, A. C., ed., Design and Analysis of Cold‐Formed Sections, Halsted Press, John Wiley & Sons, Inc., New York, N.Y., 1975, pp. 64–72.
24.
Wakabayashi, M., Matsui, B., and Mitani, I., “Cyclic Behavior of a Restrained Steel Brace Under Axial Loading,” Proceedings IV World Conference on Earthquake Engineering, Vol. 3, New Delhi, India, Jan., 1977, pp. 3181–3187.
25.
Whitmore, R. E., “Experimental Investigation of Stresses in Gusset Plates,” Univ. of Tennessee Engineering Experiment Station Bulletin, No. 16, May, 1952.
Information & Authors
Information
Published In
Copyright
Copyright © 1984 ASCE.
History
Published online: Sep 1, 1984
Published in print: Sep 1984
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.