Determining Operating Inlet Pressure Head Incorporating Uniformity Parameters for Multioutlet Plastic Pipelines
Publication: Journal of Irrigation and Drainage Engineering
Volume 134, Issue 3
Abstract
An important objective of a microirrigation system is to determine the proper operating inlet pressure head, ensuring the desired level of water application uniformity as well as the allowable pressure head variation along the multioutlet pipeline. This paper offers, simple, direct, but sufficiently accurate, relationships incorporating different microirrigation uniformity parameters, such as Christiansen uniformity coefficient, coefficient of variation of emitter discharge, and allowable pressure head variation, to determine the operating inlet pressure head (i.e., pressure head and outflow profiles) for multioutlet plastic pipelines. In this analysis some mathematical expressions were deduced to relate three uniformity parameters; then the operating inlet pressure head is simply reformulated by taking into account a multiplying factor to the required average outlet pressure head, in terms of three uniformity parameters. Resulting, the influence of different uniform pipe slopes on the water application uniformity and the operating inlet pressure head for various emitter discharge exponents, was evaluated. In addition, to cover various design combinations an extensive comparison between the proposed equations and those of the previous studies was also presented. Examination of the results from this research indicated that, the performance of the proposed technique is sufficient in comparison to those of the recent analytical and numerical procedures.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writer thanks the Editor and four anonymous reviewers for providing constructive reviews and clear criticisms on the content of the paper.
References
Anyoji, H., and Wu, I. P. (1987). “Statistical approach for drip lateral design.” Trans. ASAE, 30(1), 187–192.
Bagarello, V., Ferro, V., Provenzano, G., and Pumo, D. (1995). “Experimental study on flow-resistance law for small-diameter plastic pipes.” J. Irrig. Drain. Eng., 121(5), 313–316.
Blasius, H. (1913). “Das Aehnlichkeitsgesetz bei Reibungsavorgangen.” Flussigkeiten Forschungsarbeiten auf dem Gebiete des Ingenieurwesens, 131(1) (in German).
Bralts, V. F., Edwards, D. M., and Wu, I. P. (1987). “Drip irrigation design and evaluation based on the statistical uniformity concept.” Advances in irrigation, Vol. 4, Academic, New York, 67–117.
Bralts, V. F., Wu, I. P., and Gitlin, H. M. (1981). “Manufacturing variation and drip irrigation uniformity.” Trans. ASAE, 24(1), 1234–1240.
Christiansen, J. E. (1942). “Irrigation by sprinkling.” California Agricultural Experimental Station Bulletin No. 670, Univ. of California, Davis, Calif.
Hathoot, H. M., Al-Amoud, A. I., and Mohammad, F. S. (1993). “Analysis and design of trickle irrigation laterals.” J. Irrig. Drain. Eng., 119(5), 756–767.
Juana, L., Losada, A., Rodrigoez-Sinobas, L., and Sanchez, R. (2004). “Analytical relationships for designing rectangular drip irrigation units.” J. Irrig. Drain. Eng., 130(1), 47–59.
Juana, L., Rodriguez-Sinobas, L., and Losada, A. (2002). “Determining minor head losses in drip irrigation laterals. II: Experimental study and validation.” J. Irrig. Drain. Eng., 128(6), 385–396.
Kang, Y. (2000). “Effect of operating pressures on microirrigation uniformity.” Irrig. Sci., 20, 23–27.
Kang, Y., and Nishiyama, S. (1996). “Analysis and design of microirrigation laterals.” J. Irrig. Drain. Eng., 122(2), 75–82.
Keller, J., and Bliesner, R. D. (1990). Sprinkler and trickle irrigation, Van Nostrand Reinhold, New York.
Keller, J., and Karmelli, D. (1974). “Trickle irrigation design parameters.” Trans. ASAE, 17(4), 678–684.
Mahar, P. S., and Singh, R. P. (2003). “Computing inlet pressure head of multioutlet pipeline.” J. Irrig. Drain. Eng., 129(6), 464–467.
Perold, R. P. (1977). “Design of irrigation pipe laterals with multiple outlets.” J. Irrig. and Drain. Div., 103(2), 179–195.
Provenzano, G., Pumo, D., and Di Dio, P. (2005). “Simplified procedure to evaluate head losses in drip irrigation laterals.” J. Irrig. Drain. Eng., 131(6), 525–532.
Ravikumar, V., Ranganathan, C. R., and Santhana, Bosu S. (2003). “Analytical equation for variation of discharge in drip irrigation laterals.” J. Irrig. Drain. Eng., 129(4), 295–298.
Valiantzas, J. D. (1998). “Analytical approach for direct drip lateral hydraulic calculation.” J. Irrig. Drain. Eng., 124(6), 300–305.
Valiantzas, J. D. (2005). “Discussion of ‘Linear solution for hydraulic analysis of tapered microirrigation laterals by G. Yıldırım, and N. Ağıralioğlu.’” J. Irrig. Drain. Eng., 131(5), 487–489.
von Bernuth, R. D. (1990). “Simple and accurate friction loss equation for plastic pipe.” J. Irrig. Drain. Eng., 116(2), 294–298.
von Bernuth, R. D., and Wilson, T. (1989). “Friction factors for small diameter plastic pipes.” J. Hydraul. Eng., 115(2), 183–192.
Watters, G. Z., and Keller, J. (1978). “Trickle irrigation tubing hydraulics.” Presented at the Summer Meeting of ASAE, Paper No. 78-2015.
Wu, I. P. (1992). “Energy gradient line approach for direct hydraulic calculation in drip irrigation design.” Irrig. Sci., 13, 21–29.
Wu, I. P. (1997). “An assessment of hydraulic design of micro-irrigation systems.” Agric. Water Manage., 32, 275–284.
Yıldırım, G. (2006). “Hydraulic analysis and direct design of multiple outlets pipelines laid on flat and sloping lands.” J. Irrig. Drain. Eng., 132(6), 537–552.
Yıldırım, G. (2007a). “Analytical relationships for designing multiple outlets pipelines.” J. Irrig. Drain. Eng., 133(2), 140–154.
Yıldırım, G. (2007b). “An assessment of hydraulic design of trickle laterals considering effect of minor losses.” Irrig. Drain., 56(4), 399–421.
Yıldırım, G., and Ağıralioğlu, N. (2004). “Comparative analysis of hydraulic calculation methods in design of micro-irrigation laterals.” J. Irrig. Drain. Eng., 130(3), 201–217.
Yitayew, M., and Warrick, A. W. (1988). “Trickle lateral hydraulics. II: Design and examples.” J. Irrig. Drain. Eng., 114(2), 289–300.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Jan 5, 2007
Accepted: Sep 20, 2007
Published online: Jun 1, 2008
Published in print: Jun 2008
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.