Three-Dimensional Modeling of Sediment Transport in a Narrow 90° Channel Bend
Publication: Journal of Hydraulic Engineering
Volume 131, Issue 10
Abstract
A three-dimensional numerical model was used for calculating the velocity and bed level changes over time in a 90° bended channel. The numerical model solved the Reynolds-averaged Navier-Stokes equations in three dimensions to compute the water flow and used the finite-volume method as the discretization scheme. The model predicted the turbulence, and the SIMPLE method computed the pressure. The suspended sediment transport was calculated by solving the convection diffusion equation and the bed load transport quantity was determined with an empirical formula. The model was enhanced with relations for the movement of sediment particles on steep side slopes in river bends. Located on a transversally sloping bed, a sediment particle has a lower critical shear stress than on a flat bed. Also, the direction of its movement deviates from the direction of the shear stress near the bed. These phenomenona are considered to play an important role in the morphodynamic process in sharp channel bends. The calculated velocities as well as the bed changes over time were compared with data from a physical model study and good agreement was found.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgment
The study was supported by the Norwegian Research Council, BeMatA Program.
References
Brookes. (1963). “Discussion of ‘Boundary shear stresses in curved trapezoidal channels,’ by A. T. Ippen and P. A. Drinker.” J. Hydraul. Div., Am. Soc. Civ. Eng., 89(3), 327–333.
Demuren, A. O. (1989). “Calculation in sediment transport in meandering channels.” Proc., 23rd IAHR Congress, International Association for Hydraulic Research, Delft, The Netherlands.
Demuren, A. O. (1991). “Development of a mathematical model for sediment transport in meandering rivers.” Rep. 693, Institute for Hydromechanics, University of Karlsruhe, Karlsruhe, Germany.
Demuren, A. O., and Rodi, W. (1986). “Calculation of flow and pollutant dispersion in meandering channels.” J. Fluid Mech., 172, 63–92.
Engelund, F. (1974). “Flow and bed topography in channel bends.” J. Hydraul. Div., Am. Soc. Civ. Eng., 100(11), 1631–1648.
Engelund, F. (1981). “The motion of sediment particles on an inclined bed.” Progress Rep. 53, Institute for Hydrodynamic and Hydraulic Engineering, Technical University of Denmark, Copenhagen, Denmark.
Kawai, S., and Julien, P. (1996). “Point bar deposit in narrow sharp bends.” J. Hydraul. Res., 34(2), 205–218.
Kikkawa, H., Kitagawa, A., and Ikeda, S. (1976). “Flow and bed topography in curved open channels.” J. Hydraul. Div., Am. Soc. Civ. Eng., 102(9), 1327–1342.
Odgaard, A. J. (1981). “Transverse bed slope in alluvial channel bends.” J. Hydraul. Div., Am. Soc. Civ. Eng., 107(12), 1677–1694.
Olesen, K. W. (1987). “Bed topography in shallow river bends.” PhD thesis, Delft University of Technology, Delft, The Netherlands.
Olsen, N. R. B. (2002a). A three dimensional numerical model for simulation of sediment movement in water intakes with multi-block option: User’s manual, Dept. of Hydraulic and Environmental Engineering, Norwegian University of Science and Technology, Trondheim, Norway.
Olsen, N. R. B. (2002b). Hydroinformatics, fluvial hydraulics, and limnology, Dept. of Hydraulic and Environmental Engineering, Norwegian University of Science and Technology, Trondheim, Norway.
Olsen, N. R. B. (2003). “Three dimensional CFD modeling of self-forming meandering channel.” J. Hydraul. Eng., 129(10), 366–372.
Patankar, S. V. (1980). Numerical heat transfer and fluid flow, Taylor and Francis, London.
Rodi, W. (1980). Turbulence models and their application in hydraulics, Int. Assoc. of Hydraulic Engineering and Research, Delft, The Netherlands.
Rüther, N., and Olsen, N. R. B. (2003a). “CFD modeling of meandering river evolution.” Proc., 30th IAHR Congress, Int. Assoc. for Hydraulic Research, Delft, The Netherlands.
Rüther, N., and Olsen, N. R. B. (2003b). “CFD modeling of alluvial channel instabilities.” Proc., 3rd IAHR Symp. on River, Coastal, and Estuarine Morphodynamics, Int. Assoc. for Hydraulic Research, Delft, The Netherlands.
van Bendegom, L. (1947). “Some flow considerations on river morphology and river improvements.” De Ingenieur, 59(4), B1–B11 (in Dutch).
van Rijn, L. C. (1984a). “Sediment transport. Part I: Bed load transport.” J. Hydraul. Eng., 110(10), 1431–1456.
van Rijn, L. C. (1984b). “Sediment transport. Part II: Suspended load transport.” J. Hydraul. Eng., 110(11), 1613–1641.
Wilson, C. A. M. E., Boxall, J. B., Guymer, I., and Olsen, N. R. B. (2003). “Validation of a three dimensional numerical code in the simulation of pseudo-natural meandering flows.” J. Hydraul. Eng., 129(10), 758–768.
Wu, W., Rodi, W., and Wenka, T. (2000). “3D numerical modeling of flow and sediment transport in open channels.” J. Hydraul. Eng., 126(1), 4–15.
Information & Authors
Information
Published In
Copyright
© ASCE.
History
Received: Dec 30, 2003
Accepted: Dec 9, 2004
Published online: Oct 1, 2005
Published in print: Oct 2005
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.