Flow and Bed Topography in Alluvial Channel Bend
Publication: Journal of Hydraulic Engineering
Volume 110, Issue 4
Abstract
TWO recently developed analytical approaches to a description of the fully developed flow and bed topography in alluvial channel bends are extended to include a description of the development of the flow and bed topography in the initial portion of bends. The approaches have been verified by tests in a laboratory‐channel bend. The results of the study show that the bed topography develops and decays over a much shorter distance than does the velocity profile. The eccentricity of the centers of volume flux appears to oscillate along the channel with a period that is comparable to that predicted by a meander theory. The analyses are limited to the central portion of the channel cross section, where bank effects are negligible.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Anderson, A. G., “On the Development of Stream Meanders,” Proceedings of the 12th Congress of the International Association for Hydraulic Research, Fort Collins, Colo., Vol. 1, Paper A46, Sept., 1967, pp. 370–378.
2.
Anderson, A. G., Paintal, A. S., and Davenport, J. T., “Tentative Design Procedures for Riprap‐Lined Channels,” Report 108, National Cooperative Highway Research Program, Highway Research Board, National Research Council, 1970.
3.
DeVriend, H. J., and Koch, F. G., “Flow of Water in a Curved Open Channel with a Fixed Plane Bed,” T.O.W. Report R657‐V/M1415‐1, Delft Hydraulics Laboratory, Delft University of Technology, Delft, The Netherlands, Oct., 1977.
4.
Falcon, M. A., “Analysis of Flow in Alluvial Channel Bends,” thesis presented to the University of Iowa, at Iowa City, Iowa, in 1979, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
5.
Falcon, M. A., and Kennedy, J. F., “Flow in Alluvial‐River Curves,” Journal of Fluid Mechanics, Vol. 103, Aug., 1983.
6.
Henderson, F. M., Open Channel Flow, MacMillan Publishing Co., Inc., New York., N.Y., 1966.
7.
Karim, M. F., “Computer Based Sediment Discharge and Friction Factor Relationships for Alluvial Streams,” thesis presented to the University of Iowa in 1981, at Iowa City, Iowa, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
8.
Kikkawa, H., Ikeda, S., and Kitagawa, A., “Flow and Bed Topography in Curved Open Channels,” Journal of the Hydraulics Division, ASCE, Vol. 102, No. HY9, Proc. Paper 12416, Sept., 1976, pp. 1327–1342.
9.
Mockmore, C. A., “Flow around Bends in Stable Channels,” Transactions, ASCE, Vol. 109, Paper No. 2217, 1944, pp. 593–628.
10.
Nunner, W., “Warmeubergang und Druckabfall in rauhen Rohren,” VDI‐Forschungsheft 455, Series B, Band 2, 1956.
11.
Odgaard, A. J., “Transverse Bed Slope in Alluvial Channel Bends,” Journal of the Hydraulics Division, ASCE, Vol. 107, No. HY12, Dec., 1981, pp. 1677–1694.
12.
Odgaard, A. J., “Bed Characteristics in Alluvial Channel Bends,” Journal of the Hydraulics Division, ASCE, Vol. 108, No. HY11, Nov., 1982.
13.
Odgaard, A. J., and Kennedy, J. F., “Analysis of Sacramento River Bend Flows, and Development of a New Method for Bank Protection,” IIHR Report No. 241, Iowa Institute of Hydraulic Research, University of Iowa, Iowa City, Iowa, 1982.
14.
Odgaard, A. J., and Kennedy, J. F., “River‐Bend Bank Protection by Submerged Vanes,” Journal of Hydraulic Engineering, ASCE, Vol. 109, No. 8, Aug., 1983, pp. 1161–1173.
15.
Rozovskii, L. L., “Flow of Water in Bends of Open Channels,” Israel Program for Scientific Translations, Jerusalem, Israel, 1961 (available from U.S. Department of Commerce, National Technical Information Service, Springfield, Va. 22161).
16.
Shields, A., “Anvendung der Aenlichkeitsmechanik und der Turbulenzforschung auf die Geshiebebewegung,” Mitteilungen der Preussischen Versuchsanstalt fur Wasserbau and Schiffbau, Berlin, Germany, Translated to English by W. P. Ott and J. C. van Uchelen, California Institute of Technology, Pasadena, Calif., 1936.
17.
Shukry, A., “Flow around Bends in an Open Flume,” Transactions, ASCE, Vol. 115, Paper No. 2411, 1950, pp. 751–788.
18.
Simons, D. B., and Senturk, F., Sediment Transport Technology, Water Resource Publications, Fort Collins, Colo., 1977.
19.
Strickler, A., “Beitrage zur Frage der Geschwindigheits formel und der Rauhigkeitszahlen fur Strome, Kanale und Geschlossene Leitungen,” Mitteilungen des Eidgenossischer Amtes fur Wasserwirtschaft, No. 16g, Bern, Switzerland, 1923.
20.
Werner, P. W., “On the Origin of River Meanders,” Transactions of the American Geophysical Union, Vol. 32, No. 6, 1951, pp. 898–902.
21.
Yen, B. C., “Characteristics of Subcritical Flow in a Meandering Channel,” Report, Institute of Hydraulic Research, University of Iowa, Iowa Citv, Iowa, 1965.
22.
Zimmermann, C., and Kennedy, J. F., “Transverse Bed Slopes in Curved Alluvial Streams,” Journal of the Hydraulics Division, ASCE, Vol. 104, No. HY1, Jan., 1978, pp. 33–48.
Information & Authors
Information
Published In
Copyright
Copyright © 1984 ASCE.
History
Published online: Apr 1, 1984
Published in print: Apr 1984
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.