Pullout Resistance of “H” Piles
Publication: Journal of Geotechnical Engineering
Volume 110, Issue 9
Abstract
Pullout capacities of driven H piles under axial tension loads were determined experimentally in stiff clays, dense sands, silts, and stratified soils. The test results are interpreted by 3 different procedures. Measured pullout capacities are compared to predicted pullout capacities based on semi‐empirical approaches. Predicted capacities vary greatly with subsurface conditions of site, effective failure surfaces of piles, pile lengths, and soil shear strength parameters. Earth pressure parameters and adhesion values obtained from the tension load tests are generally found to be consistent with the previously published data.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Bishop, A. W., Discussion in Behavior of Piles, Institution of Civil Engineers, London, England, 1971, pp. 31–33.
2.
Blessey, W. E., “Allowable Pile Capacity, Mississippi River Deltaic Plain,” Conference on Design and Installation of Pile Foundations and Cellular Structures, Lehigh University, Bethlehem, Pa., 1970, pp. 87–106.
3.
Bowles, J. E., Foundation Analysis and Design, McGraw‐Hill Book Co., Inc., New York, N.Y., 1982, pp. 602–608.
4.
Burland, J. B., “Shaft Friction of Piles in Clay—A Simple Fundamental Approach,” Ground Engineering, Vol. 6, No. 3, 1973, pp. 30–42.
5.
Chellis, R. D., Pile Foundations, McGraw‐Hill Book Co., Inc., New York, N.Y., 1961, pp. 465–467.
6.
Design Manual—Soil Mechanics, Foundations and Earth Structures, Department of the Navy, NAVFAC, DM‐7, Jan., 1971, pp. 7–13–12.
7.
Flaate, K., and Selnes, P., “Side Friction of Piles in Clay,” Proceedings of the Ninth International Conference on Soil Mechanics and Foundation Engineering, Tokyo, Japan, Vol. 1, 1977, pp. 517–522.
8.
Haswell, C. K., and Burland, J. B., “The Prediction of Load Carrying Capacity of Piles,” Piles and Pile Foundations, F. E. Young, ed., Thomas Telford Ltd., London, England, 1981, pp. 135–142.
9.
Ireland, H. O., “Pulling Tests on Piles in Sand,” Proceedings Fourth International Conference on Soil Mechanics and Foundation Engineering, Vol. 2, 1957, pp. 43–54.
10.
Janbu, N., “Static Bearing Capacity of Friction Piles,” Proceedings of the European Conference on Soil Mechanics and Foundation Engineering, Vol. 1, 1976, pp. 479–488.
11.
Johnson, S. M., and Kavanaugh, T. C., The Design of Foundations for Buildings, McGraw Hill Book Co., Inc., 1968, p. 361.
12.
Kraft, L. M., Jr., Focht, J. A., Jr., and Amerasinghe, S. F., “Friction Capacity of Piles Driven Into Clays,” Journal of the Geotechnical Engineering Division, ASCE, Vol. 107, No. GT11, 1981, pp. 1521–1541.
13.
Manual of Steel Construction, American Institute of Steel Construction, Chicago, Ill., 1981, pp. 1–34.
14.
McClelland, B., Focht, J. A., Jr., and Emrich, W. J., “Problems in Design and Installation of Offshore Piles,” Journal of the Soil Mechanics and Foundation Division, ASCE, Vol. 95, No. SM6, 1969.
15.
Meyerhof, G. G., “Bearing Capacity and Settlement of Pile Foundations,” Journal of the Geotechnical Engineering Division, ASCE, Vol. 102, No. GT3, 1976, pp. 197–228.
16.
Mohan, D., and Chandra, S., “Frictional Resistance of Bored Piles in Expansive Clays,” Geotechnique, Vol. 11, 1961, p. 291.
17.
Peck, R. B., Hanson, W. E., and Thornburn, T. H., Foundation Engineering, John Wiley & Sons, Inc., New York, N.Y., 1974, pp. 214–261.
18.
Poulos, H. G., and Davis, E. H., Pile Foundation Analysis and Design, John Wiley & Sons, Inc., New York, N.Y., 1980.
19.
Recommended Practice for Planning, Designing, and Construction, Fixed Offshore Platforms, American Petroleum Institute, API RP 2A, 11th ed., 1980.
20.
Sowa, V. A., “Pulling Capacity of Concrete Cast In Situ Bored Piles,” Canadian Geotechnical Journal, Vol. 7, 1970, pp. 482–493.
21.
Skempton, A. W., “Cast‐In Situ Bored Piles in London Clay,” Geotechnique, Vol. 9, 1959, p. 158.
22.
“Standard Method of Testing Piles Under Static Axial Compressive Load,” Annual Book of ASTM Standards, American Society for Testing and Materials Designation D‐1143, Part 19, 1982, pp. 238–253.
23.
Tomlinson, M. J., “The Adhesion of Piles Driven in Clay Soils,” Proceedings Fourth International Conference, Soil Mechanics and Foundation Engineering, Vol. 2, 1957, pp. 66–71.
24.
Tomlinson, M. J., “Some Effects of Pile Driving on Skin Friction,” Proceedings Institution of Civil Engineers Conference: Behavior of Piles, London, England, 1971, pp. 107–114.
25.
Turner, E. A., “Uplift Resistance of Transmission Tower Footings,” Journal Power Division of American Society of Civil Engineers, Vol. 88, Paper 3187, 1962.
26.
Vesic, A. S., “Design of Pile Foundations,” Transportation Research Board, National Research Council, Washington, D.C., 1977, pp. 14–22.
27.
Vijayvergiya, V. A., and Focht, J. A., Jr., “A New Way to Predict Capacity of Piles in Clays,” Proceedings of the Fourth Offshore Technology Conference, Houston, Tex., Vol. 2, 1972, pp. 865–874.
28.
Wright, S. G., “A Study of Slope Stability and the Undrained Shear Strength of Clay Shales,” thesis presented to the University of California, at Berkeley, Calif., in 1969, in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
Information & Authors
Information
Published In
Copyright
Copyright © 1984 ASCE.
History
Published online: Sep 1, 1984
Published in print: Sep 1984
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.