Transverse Shear Including Skin Effect for Composite Sandwich with Honeycomb Sinusoidal Core
Publication: Journal of Engineering Mechanics
Volume 133, Issue 3
Abstract
Honeycomb fiber-reinforced polymer (HFRP) sandwich panels with sinusoidal core geometry have been used extensively for new construction and replacement of bridge decks. The core geometry used consists of large cavities and represents a new type of core configuration. This study is concerned with the behavior of HFRP panels under transverse shear considering skin effect, and addresses the two contributing factors due to shear warping and bending warping. Shear warping corresponds to the assumption of having a hinge connection between facesheet and core, and bending warping is induced for the assumption of a rigid connection. All previous studies have been focused mainly on shear warping, neglecting for the most part bending warping. A closed-form solution based on proper description of displacement field at the interface is derived considering shear warping. The accuracy of this solution is verified by finite-element (FE) results. The FE model is then applied to study bending warping effect, and also the core-facesheet constraint or interface bonding effect. The equivalent shear stiffness and the stress distributions subject to skin effect are defined, and suggestions for future design considerations are given.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Partial financial support for this study was received from the National Science Foundation Partnerships for Innovation program and the West Virginia University Research Corporation. The authors appreciate the valuable comments and suggestions by the reviewers of this paper.
References
ABAQUS. (2002). ABAQUS user’s manual, version 6.3, HKS, Inc., Providence, R.I.
Allen, H. G. (1969). Analysis and design of structural sandwich panels, Pergamon, Tarrytown, N.Y.
Becker, W. (1998). “The inplane stiffness of a honeycomb core including the thickness effect.” Arch. Appl. Mech., 68(5), 334–341.
Blackman, B. R. K., Hadavinia, H., Kinloch, A. J., and Williams, J. G. (2003). “The use of a cohesive zone model to study the fracture of fiber composites and adhesively-bonded joints.” Int. J. Fract., 119, 25–46.
Burton, W. Scott, and Noor, A. K. (1997). “Structural analysis of the adhesive bond in a honeycomb core sandwich panel.” Finite Elem. Anal. Design, 26(3), 213–227.
Chen, A. (2004). “Strength evaluation of honeycomb FRP sandwich panels with sinusoidal core geometry.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, West Virginia Univ., Morgantown, W.V.
Chen, A., and Davalos, J. F. (2003). “Bending strength of honeycomb FRP sandwich beams with sinusoidal core geometry.” Proc., CANCOM 2003, Canadian Society of Civil Engineers, Ottawa, Canada.
Chen, A., and Davalos, J. F. (2005). “A solution including skin effect for stiffness and stress field of sandwich honeycomb core.” Int. J. Solids Struct., 42(9–10), 2711–2739.
Christensen, R. M. (1991). Mech. compos. mater., Krieger Publishing Company, Malabar, Fla.
Cui, W., and Wisnom, M. R. (1992). “A combined stress-based and fracture-mechanics-based model for predicting delamination in composites.” Composites, 24(6), 467–474.
Davalos, J. F., and Chen, A. (2005). “Buckling behavior of honeycomb FRP core with partially restrained loaded edges under out-of-plane compression.” J. Compos. Mater., 39(16), 1465–1485.
Davalos, J. F., Qiao, P., Xu, F X., Robinson, J., and Barth, K. E. (2001). “Modeling and characterization of fiber-reinforced plastic honeycomb sandwich panels for highway bridge applications.” Compos. Struct., 52(3–4), 441–452.
El-Sayed, S., and Sridharan, S. (2002). “Cohesive layer model for predicting delamination growth and crack kinking in sandwich structures.” Int. J. Fract., 117(1), 63–84.
Gibson, J. L., and Ashby, M. F. (1988). Cellular solids, structure, and properties, Pergamon, Oxford, U.K.
Grediac, M. (1993). “A finite element study of the transverse shear in honeycomb cores.” Int. J. Solids Struct., 30(13), 1777–1788.
Kelsey, S., Gellatly, R. A., and Clark, B. W. (1958). “The shear modulus of foil honeycomb cores.” Aircr. Eng., 30, 294–302.
Noor, A. K., Burton, W. S., and Bert, C. W. (1996). “Computational models for sandwich panels and shells.” Appl. Mech. Rev., 49(3), 155–199.
Papadopoulos, Lampros, Kassapoglou, and Christos. (2004). “Shear buckling of rectangular composite plates with two concentric layups.” J. Reinf. Plast. Compos., 23(1), 5–16.
Penzien, J., and Didriksson, T. (1964). “Effective shear modulus of honeycomb cellular structure.” AIAA J., 2(3), 531–535.
Plunkett, J. D. (1997). “Fiber-reinforcement polymer honeycomb short span bridge for rapid installation.” Idea Project Rep., Contract NCHRP-96-ID030, Transportation Research Board, National Research Council, Washington, D.C.
Qiao, P., Davalos, J. F., and Wang, J. (2001). “Local buckling of composite FRP shapes by discrete plate analysis.” J. Struct. Eng., 127(3), 245–255.
Ungsuwarungsri, T., and Knauss, W. K. (1987). “The role of damage-soften material behavior in the fracture of composites and adhesives.” Int. J. Fract., 35(3), 221–241.
Vinson, J. R. (1999). The behavior of sandwich structures of isotropic and composite material, Technomic Publishing Company, Inc., Lancaster, Pa.
Wang, and Weiqiao. (2004). “Cohesive zone model for facesheet-core interface delamination in honeycomb FRP sandwich panels.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, West Virginia Univ., Morgantown, W.V.
Xu, F. X., and Qiao, P. (2002). “Homogenized elastic properties of honeycomb sandwich with skin effect.” Int. J. Solids Struct., 39(8), 2153–2188.
Xu, F. X., Qiao, P., and Davalos, J. F. (2001). “Transverse shear stiffness of composite honeycomb core with general configuration.” J. Eng. Mech., 127(11), 1144–1151.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Sep 2, 2004
Accepted: May 25, 2006
Published online: Mar 1, 2007
Published in print: Mar 2007
Notes
Note. Associate Editor: Ronald Y. S. Pak
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.