Hyperelasticity Model for Finite Element Analysis of Natural and High Damping Rubbers in Compression and Shear
Publication: Journal of Engineering Mechanics
Volume 132, Issue 1
Abstract
Rate-independent monotonic behavior of filled natural rubber and high damping rubber is investigated in compression and shear regimes. Monotonic responses obtained from tests conducted in both regimes demonstrate the prominent existence of the Fletcher–Gent effect, indicated by high stiffness at low strain levels. An improved hyperelasticity model for compression and shear regimes is proposed to represent the rate-independent instantaneous and equilibrium responses including the Fletcher–Gent effect. A parameter identification scheme involving simultaneous minimization of least-square residuals of uniaxial compression and simple shear data is delineated. The difficulties of identifying a unique set of hyperelasticity parameters that hold for both compression and shear deformation modes are thus overcome. The proposed hyperelasticity model has been implemented in a general purpose finite element program. Finite element simulations of experiments have shown the adequacy of the proposed hyperelasticity model, estimated parameters, and employed numerical procedures. Finally, numerical experiments were conducted to further explore the potential of the proposed model, and estimated parameters in analyzing rubber layers of a base isolation bearing subjected either to compression or to a combination of compression and shear.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers are very grateful to Professor H. Horii, Department of Civil Engineering, University of Tokyo, Japan for his valuable comments and suggestions and particularly for allowing them to use the experimental facilities of his laboratory to carry out the mechanical tests in the investigation. The writers gratefully acknowledge the kind cooperation extended by the Yokohama Rubber Co. by providing test specimens. The writers also sincerely appreciate the funding provided by the Japanese Ministry of Education, Science, Sports, and Culture as a Grant-in-Aid for Scientific Research (C) (Grant No. MESSC-JP12650457) to carry out this research.
References
ABAQUS (1996). Theory manual, Version 5.6, Hibbitt, Karlsson & Sorensen, Inc., Providence, R.I.
Ahmadi, H. R., Kingston, J. G. R, Muhr, A. H., Gracia, L. A., and Gómez, B. (2003). “Interpretation of the high–low-strain modulus of filled rubbers as an inelastic effect.” Proc., 3rd European Conf. on Constitutive Models for Rubber, J. Busfield and A. Muhr, eds., Balkema, Rotterdam, The Netherlands, 357–364.
Aklonis, J. J., Macnight, W. J., and Shen, M. (1972). Introduction to polymer viscoelasticity, Wiley, Toronto, Canada.
Alexander, H. (1968). “A constitutive relation for rubber-like materials.” Int. J. Eng. Sci., 6, 549–563.
Ali, H. M., and Abdel-Ghaffar, A. M. (1995). “Modeling of rubber and lead passive-control bearings for seismic analysis.” J. Struct. Eng., 121(7), 1134–1144.
American Association for State Highway and Transportation Officials (AASHTO). (1992). Standard specifications for highway bridges, 15th Ed., Washington, D.C.
Amin, A. F. M. S. (2001). “Constitutive modeling for strain-rate dependency of natural and high damping rubbers.” PhD thesis, Saitama Univ., Saitama, Japan.
Amin, A. F. M. S., Alam, M. S., and Okui, Y. (2002). “An improved hyperelasticity relation in modeling viscoelasticity response of natural and high damping rubbers in compression: Experiments, parameter identification, and numerical verification.” Mech. Mater., 34, 75–95.
Amin, A. F. M. S., Alam, M. S., and Okui, Y. (2003). “Measurement of lateral deformation of natural and high damping rubbers in large deformation uniaxial tests.” J. Test. Eval., 31(6), 524–532.
Anand, L. (1996). “A constitutive model for compressible elastomeric solids.” Comput. Mech., 18, 339–355.
Arruda, E. M., and Boyce, M. C. (1993). “A three-dimensional constitutive model for the large stretch behavior of rubber elastic materials.” J. Mech. Phys. Solids, 41, 389–412.
Bhuiyan, A. R. (2004). “Finite element modeling for nonlinear elastic response of natural and high damping rubber.” MSc thesis, Bangladesh Univ. of Engineering and Technology, Bangladesh.
Bonet, J., and Wood, R. D. (1997). Nonlinear continuum mechanics for finite element analysis, Cambridge Univ. Press, Cambridge, U.K.
Boyce, M. C., and Arruda, E. M. (2000). “Constitutive models of rubber elasticity: A review.” Rubber Chem. Technol., 73, 504–523.
Bueche, F. (1960). “Mechanical degradation of high polymers.” J. Appl. Polym. Sci., 4, 101–106.
Carr, A. J., Cooke, N., and Moss, P. J. (1996). “Compression behavior of bridge bearings used for seismic isolation.” Eng. Struct., 18, 351–362.
Castellani, A., Kajon, G., Panzeri, P., and Pezzoli, P. (1998). “Elastomeric materials used for vibration isolation of Railaway Lines.” J. Eng. Mech., 124(6), 614–621.
Chang, C. (2002). “Modeling of laminated rubber bearings using an analytical stiffness matrix.” Int. J. Solids Struct., 39, 6055–6078.
Charlton, D. J., Yang, J., and Teh, K. K. (1994). “A review of methods to characterize rubber elastic behavior for use in finite element analysis.” Rubber Chem. Technol., 67, 481–503.
Chen, Y., and Ahmadi, G. (1992). “Wind effects on base-isolated structures.” J. Eng. Mech., 118(8), 1708–1727.
Davis, C. K. L., De, D. K., and Thomas, A. G. (1994). “Characterization of the behavior of rubber for engineering design purposes. 1: Stress–strain relations.” Rubber Chem. Technol., 67, 716–728.
Dorfmann, A., and Burtscher, S. L. (2000). “Aspects of cavitation damage in seismic bearings.” J. Struct. Eng., 126(5), 573–579.
European Commission (1999). “Highly adaptable rubber isolating system (HARIS).” Final Technical Rep. Contract No. BRPR-CT95-0072, Project No. Be-1258.
Fletcher, W. P., and Gent, A. N. (1953). “Non-linearity in the dynamic properties of vulcanized rubber compounds.” Trans. Inst. Rubber Industry, 29, 266–280.
Fujita, T., Fujita, S., Tazaki, S., Yoshizawa, T., and Suzuki, S. (1990). “Research, development and implementation of rubber bearings for seismic isolations.” JSME Int. J., Ser. I, 33, 394–403.
Gendy, A. S., and Saleeb, A. F. (2000). “Nonlinear material parameter estimation for characterizing hyperelastic large strain models.” Comput. Mech., 25, 66–77.
Gent, A. N. (1962a). “Relaxation processes in vulcanized rubber. I: Relation among stress relaxation, creep, recovery, and hysteresis.” J. Appl. Polym. Sci., 6, 33–441.
Gent, A. N. (1962b). “Relaxation processes in vulcanized rubber. II: Secondary relaxation due to network breakdown.” J. Appl. Polym. Sci., 6, 442–448.
Häggblad, B., and Sundberg, J. A. (1983). “Large strain solutions for rubber components.” Comput. Struct., 17, 835–843.
Hamzeh, O. N., Tassoulas, J. L., and Becker, E. B. (1998). “Behavior of elastomeric bridge bearings: Computational results.” J. Bridge Eng., 3(3), 140–146.
Hart-Smith, L. J. (1966). “Elasticity parameters for finite deformations of rubber-like materials.” Z. Angew. Math. Phys., 17, 608–626.
Herrmann, L. R., Hamidi, R., Shafigh-Nobari, F., and Lim, C. K. (1988a). “Nonlinear behavior of elastomeric bearings. I: Theory.” J. Eng. Mech., 114(11), 1811–1830.
Herrmann, L. R., Hamidi, R., Shafigh-Nobari, F., and Ramaswamy, A. (1988b). “Nonlinear behavior of elastomeric bearings. II: FE analysis and verification.” J. Eng. Mech., 114(11), 1831–1853.
Herrmann, L. R., Ramaswamy, A., and Hamidi, R. (1989). “Analytical parameter study for class of elastomeric bearings.” J. Struct. Eng., 115(10), 2415–2434.
Huber, N., and Tsakmakis, C. (2000). “Finite deformation viscoelasticity laws.” Mech. Mater., 32, 1–18.
Hwang, J. S., and Ku, S. W. (1997). “Analytical modeling of high damping rubber bearings.” J. Struct. Eng., 123(8), 1029–1036.
Imbimbo, M., and Luca, A. D. (1998). “F.E. stress analysis of rubber bearings under axial loads.” Comput. Struct., 68, 31–39.
James, A. G., Green, A., and Simpson, G. M. (1975a). “Strain energy functions of rubber. I: Characterization of gum vulcanizates.” J. Appl. Polym. Sci., 19, 2033–2058.
James, A. G., and Green, A. (1975b). “Strain energy functions of rubber. II: The characterization of filled vulcanizates.” J. Appl. Polym. Sci., 19, 2319–2330.
Jankovich, E., Leblanc, F., and Durand, M. (1981). “A finite element method for the analysis of rubber parts, experimental and analytical assessment.” Comput. Struct., 14, 385–391.
Kawabata, S., and Kawai, H. (1977). “Strain energy density functions of rubber vulcanizates from biaxial extension.” Adv. Polym. Sci., 24, 90–124.
Kawabata, S., Matsuda, M., Tei, K., and Kawai, H. (1981). “Experimental survey of the strain energy density function of isoprene rubber vulcanizate.” Macromolecules, 14, 154–162.
Kelly, J. M. (1997). Earthquake resistant design with rubber, Springer-Verlag, London.
Lambert-Diani, J., and Rey, C. (1999). “New phenomenological behavior laws for rubbers and thermo plastic elastomers.” Eur. J. Mech. A/Solids, 18, 1027–1043.
Lim, C. K., and Herrmann, L. R. (1987). “Equivalent homogeneous FE model for elastomeric bearings.” J. Struct. Eng., 113(1), 106–125.
MARC (1996). MSC Software Corporation, Redwood City, Calif.
Mattheck, C., and Erb, D. (1991). “Shape optimization of a rubber bearing.” Int. J. Fatigue, 13, 206–208.
Mooney, M. (1940). “A theory of large elastic deformation.” J. Appl. Phys., 11, 582–592.
Mori, A., Carr, A. J., Cooke, N., and Moss, P. J. (1996). “Compression behavior of bridge bearings used for seismic isolation.” Eng. Struct., 18, 351–362.
Mullins, L. (1969). “Softening of rubber by deformations.” Rubber Chem. Technol., 42, 339–362.
Mullins, L. (1987). “Engineering with rubber.” Chem. Tech. (Leipzig), 13, 720–727.
Nicholson, D. W., Nelson, N. W., Lin, B., and Farinella, A. (1998). “Finite element analysis of hyperelastic components.” Appl. Mech. Rev., 51, 303–320.
Ogden, R. W. (1972). “Large deformation isotropic elasticity: On the correlation of theory and experiment for compressible rubberlike solids.” Proc. R. Soc. London, Ser. A, 328, 567–583.
Payne, A. R., and Whittaker, R. E. (1971). “Low strain dynamic properties of filled rubbers.” Rubber Chem. Technol., 44, 440–478.
Peng, S. H., and Chang, S. H. (1997). “A compressible approach in finite element analysis of rubber elastic materials.” Comput. Struct., 62, 573–593.
Peng, T. J., and Landel, R. F. (1972). “Stored energy function of rubberlike materials derived from simple tensile data.” J. Appl. Phys., 43, 3064–3067.
Quigley, C. J., Mead, J., and Johnson, A. R. (1995). “Large strain viscoelastic constitutive models for rubber. II: Determination of material constants.” Rubber Chem. Technol., 68, 230–247.
Ramberger, G. (2002). “Structural bearings and expansion joints for bridges.” Structural Engineering Documents 6, International Association for Bridge and Structural Engineering, Zurich, Switzerland.
Rivlin, R. S. (1948a). “Large elastic deformations of isotropic materials: Fundamental concepts.” Philos. Trans. R. Soc. London, Ser. A, 240, 459–490.
Rivlin, R. S. (1948b). “Large elastic deformations of isotropic materials IV. Further developments of the general theory.” Philos. Trans. R. Soc. London, Ser. A, 241, 379–397.
Roeder, C. W., and Stanton, J. F. (1983). “Elastomeric bearings: State-of-the-art.” J. Struct. Eng., 109(12), 2853–2871.
Seibert, D. J., and Schöche, N. (2000). “Direct comparison of some recent rubber elasticity models.” Rubber Chem. Technol., 73, 366–384.
Simo, J. C., and Taylor, R. L. (1982). “Penalty function formulations for incompressible nonlinear elastics.” Comput. Methods Appl. Mech. Eng., 35, 107–118.
Taylor, R. L. (2000). FEAP—A finite element analysis program, user manual, Version 7.3, <http://www.ce.berkeley.edu/∼rlt/feap/>, UC Berkeley.
Treloar, L. R. G. (1944). “Stress–strain data for vulcanized rubber under various types of deformations.” Trans. Faraday Soc., 29, 59–70.
Treloar, L. R. G. (1975). The physics of rubber elasticity, Clarendon, Oxford, U.K.
Tschoegl, N. W. (1972). “Constitutive equations for elastomers.” Rubber Chem. Technol., 45, 60–70.
Valanis, K. C., and Landel, R. F. (1967). “The strain-energy density function of a hyperelastic material in terms of the extension ratios.” J. Appl. Phys., 38, 2997–3002.
van den Bogert, P. A. J., and de Borst, R. (1994). “On the behavior of rubber-like materials in compression and shear.” Arch. Appl. Mech., 64, 136–146.
Ward, I. M. (1985). Mechanical properties of solid polymers, Wiley, New York.
Wiraguna, S. I. (2003). “Mechanical behavior of high damping rubber under shear deformation.” MSc thesis, Saitama Univ., Saitama, Japan.
Wolfram, S. (1999). (1999). The Mathematica Book, 4th ed., Wolfram Media/Cambridge Univ. Press.
Yamashita, Y., and Kawabata, S. (1992). “Approximated form of the strain energy density function of carbon-black filled rubbers for industrial applications.” J. Soc. Rubber Ind. (Jpn.), 65, 517–528 (in Japanese).
Yeoh, O. H. (1990). “Characterization of elastic properties of carbon-black filled rubber vulcanizates.” Rubber Chem. Technol., 63, 792–805.
Yeoh, O. H. (1993). “Some forms of strain energy function for rubber.” Rubber Chem. Technol., 66, 754–771.
Yeoh, O. H. (1997). “On the Ogden stain-energy function.” Rubber Chem. Technol., 70, 175–182.
Yoshida, J., Abe, M., and Fujino, Y. (2004a). “Constitutive model of high-damping rubber materials.” J. Eng. Mech., 130(2), 129–141.
Yoshida, J., Abe, M., and Fujino, Y., and Watanabe, H. (2004b). “Three-dimensional finite-element analysis of high damping rubber bearings.” J. Eng. Mech., 130(5), 607–620.
Zienkiewicz, O. C., and Taylor, R. L. (1996). The finite element method, 4th Ed., McGraw-Hill, New York.
Information & Authors
Information
Published In
Copyright
© 2006 ASCE.
History
Received: Jul 13, 2004
Accepted: Mar 22, 2005
Published online: Jan 1, 2006
Published in print: Jan 2006
Notes
Note. Associate Editor: Francisco Armero
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.