Glass Fiber Reinforced Polymer Pultruded Members: Constitutive Model and Stability Analysis
Publication: Journal of Engineering Mechanics
Volume 130, Issue 8
Abstract
The increasingly widespread use of fiber-reinforced polymers as an alternative to conventional materials makes it necessary to formulate theoretical models which adequately evaluate the influence of the anisotropy of such composites on the structural behavior. While the cross section shapes adopted for compressed members are generally the same as in steel structures, the anisotropy which characterizes these polymers may reduce the critical loading threshold due to local buckling phenomena. A procedure to study the buckling of glass fiber reinforced polymer pultruded members by means of an homogenization approach is proposed here. A two-stage buckling model permits the determination of both global and local critical loads as explicit functions of the member geometry and its material behavior. These functions may be used for optimization of the shape of the above-mentioned members. Besides the model shows its reliability as it fits the results of experimental testson members with different slenderness ratios.
Get full access to this article
View all available purchase options and get full access to this article.
References
Agarwal, B. D., and Broutman, L. J. (1990). Analysis and performance of fiber composites, Wiley, New York.
Anthoine, A.(1995). “Derivation of in plane elastic characteristic of masonry through homogenization theory.” Int. J. Solids Struct., 32, 137–163.
Bank, L. C. (1993). Properties of FRP reinforcement for concrete, in fiber-reinforced-plastic (FRP) reinforcement for concrete structures: Properties and applicatios, A. Nanni, ed., Elsevier, New York.
Barbero, E. J. (1998). Introduction to composite materials design, Taylor and Francis, London.
Caillerie, D.(1984). “Thin elastic and periodic plates.” Math. Methods Appl. Sci., 6, 159–191.
Castañeda, N. N., and Suquet, P.(1995). “Non linear composites.” Adv. Appl. Mech., 34, 172–295.
Cecchi, A., and Di Marco, R.(2001). “Homogenization of FRP pultruded elements: A computational procedure for designing composite materials.” Mater. Struct., 34, 378–384.
Cecchi, A., and Sab, K. (2002). “Out of plane model for heterogeneous periodic materials: The case of masonry.” Eur. J. Mech. A Solids, in press.
Flügge, W. (1962). Stress in shells, Springer, Berlin.
Hashin, Z.(1963a). “Analysis of composite materials: a survey.” J. Appl. Mech., 50, 481–505.
Hashin, Z.(1963b). “The elastic moduli of heterogeneuos materials.” J. Mech. Phys. Solids, 11, 127–140.
Hashin, Z., and Rosen, B. W.(1964). “The elastic moduli of fiber-reinforced materials.” J. Appl. Mech., 31, 223–230.
Hashin, Z., and Shtrikman, S.(1962). “On some variational principles in anisotropic and nonhomogeneous elasticity.” J. Mech. Phys. Solids, 10, 335–342.
Hill, R.(1965). “Theory of mechanical properties of fiber-strengthened materials: III. Self consistent model.” J. Mech. Phys. Solids, 13, 89–101.
Koiter, W. T. (1962). “Stability of equilibrium of continuous bodies.” Tech. Rep. No. 79, Brown Univ., Providence, R.I.
Lekhnitskii, S. G. (1968). Anisotropic plates, Gordon and Breach, New York.
Luciano, R., and Barbero, E. J.(1994). “Formulas for the stiffness of composites with periodic microstructure.” Int. J. Solids Struct., 31, 2933–2944.
Mottram, J. T., Brown, N. D., and Lane, A. (1998). “The analysis of columns for the design of pultruded frames: Isolated centrally loaded columns.” Proc., on ECCM-8 European Conf. on Composites Materials, C. Visconti, ed., Vol. 2, Naples, Italy, 235–242.
Naghdi, P. M. (1972). “The theory of shells and plates.” Handbuch der physik, Vol. VI a/2, Springer, Berlin.
Paul, B. (1960). “Predictions of elastic constants of multiphase materials.” Trans. Metall. Soc. AIME, 36–41.
Pignataro, M., Rizzi, N., and Luongo, A. (1972). Stabilità, biforcazione e comportamento postcritico delle strutture elastiche. E.S.A., Rome.
Russo, S. (2001). “Buckling of GFRP pultruded columns.” Proc., Composite in Construction, Porto, Portual, 113–118.
Sanchez-Hubert, J., and Sanchez-Palencia, E. (1992). Introduction aux mèthodes asymptotiques et à l’homogénéisation, Masson, Paris.
Tan, P., Tong, L., and Steven, G. P.(1997). “A three-dimensional modelling technique for predicting the linear elastic property of opened-packing woven fabric unit cells.” Compos. Struct., 38(1–4), 261–271.
Tan, P., Tong, L., and Steven, G. P.(2000a). “Behavior of 3D orthogonal woven CFRP composites. Part I. experimental investigation.” Composites, Part A, 31, 259–271.
Tan, P., Tong, L., Steven, G. P., and Ishikawa, T.(2000b). “Behavior of 3D orthogonal woven CFRP composites. Part II. FEA and analytical modeling approaches.” Composites, Part A, 31, 273–281.
Timoshenko, S. P., and Gere, G. M. (1961). Theory of elastic stability, Vol. 2, McGraw-Hill, New York.
Timoshenko, S. P., and Woinowsky-Krieger, S. (1959). Theory of plates and shells, McGraw-Hill, New York.
Willis, J. R.(1983). “The overall response of composite materials.” Adv. Appl. Mech., 21, 1–78.
Woo, K., and Whitcomb, J. D.(1997). “Effects of fiber tow misalignment on the engineering properties of plain weave textile composites.” Compos. Struct., 37(3/4), 343–355.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 American Society of Civil Engineers.
History
Received: Mar 8, 2002
Accepted: Dec 17, 2003
Published online: Jul 15, 2004
Published in print: Aug 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.