Three-Dimensional Finite-Element Analysis of High Damping Rubber Bearings
Publication: Journal of Engineering Mechanics
Volume 130, Issue 5
Abstract
A three-dimensional finite element modeling of high damping rubber bearings is studied. At first, the constitutive model of high damping rubber materials proposed by the writers is formulated in order to derive the constitutive tensor, which is required in the application of the finite element method. Second, a mixed finite-element method consistent with the proposed constitutive model is described. In this method, slightly compressible materials with rate form constitutive models are applied. Then, using the constitutive model and the finite-element method, a three-dimensional finite element model of high damping rubber bearings is constructed. The simulations by the model are found to be in good agreement with the experimental results of the bearing. Finally, complex deformation such as torsional or rotational deformation of the bearing are simulated by the finite-element model, and the design equations for these deformation are proposed on the basis of the simulations or experimental results.
Get full access to this article
View all available purchase options and get full access to this article.
References
Abe, M., Yoshida, J., and Fujino, Y. (2004a). “Multiaxial behaviors of laminated rubber bearings and their modeling. I: Experimental study.” J. Struct. Eng., in press.
Abe, M., Yoshida, J., and Fujino, Y. (2004b). “Multiaxial behaviors of laminated rubber bearings and their modeling. II: Modeling.” J. Struct. Eng., in press.
Aiken, I. D., Kelly, J. M., Clark, W. P., Tamura, K., Kikuchi, M., and Itoh, T. (1992). “Experimental studies of the mechanical characteristics of three types of seismic isolation bearings.” Proc., 3rd World Conf. on Earthquake Engineering, Madrid, Spain.
Ali, H. M., and Abdel-Ghaffar, A. M.(1995). “Modeling of rubber and lead passive-control bearings for seismic analysis.” J. Struct. Eng., 121(7), 1134–1144.
Bathe, K. J. (1996). Finite element procedures, Prentice-Hall, Englewood Cliffs, N.J.
Billings, L. J. (1993). “Finite element modeling of elastomeric seismic isolation bearings.” PhD dissertation, Univ. of California, Irvine, Calif.
Chaboche, L. J.(1989). “Constitutive equations for cyclic plasticity and cyclic viscoplasticity.” Int. J. Plast., 5, 247–301.
Crisfield, M. A. (1991). Non-linear finite element analysis of solids and structures, Volume 1: Essentials. Wiley, Chichester, England.
Duffett, G., and Reddy, B. D.(1983). “The analysis of incompressible hyperelastic bodies by the finite element method.” Comput. Methods Appl. Mech. Eng., 41(1), 105–208.
Gandala, M. S.(1992). “Alternative methods for the solution of hyperelastic problems with incompressibility.” Comput. Struct., 42(1), 1–10.
Hisada, T., and Noguchi, H. (1995). Basis and application of nonlinear finite element method, Maruzen, Tokyo (in Japananese).
Hwang, J. S., and Ku, S. W.(1997). “Analytical modeling of high damping rubber bearings.” J. Struct. Eng., 123(8), 1029–1036.
Japan Road Association. (1991). Design specification of the bearing for highway bridges. Maruzen, Tokyo (in Japanese).
Kelly, J. M. (1991). “Dynamic and failure characteristics of bridgestone isolation bearings.” EERC Rep. No. 515/K34, Earthquake Engineering Research Center, Univ. of California, Berkeley, Calif.
Khan, A. S., and Huang, S. (1995). Continuum theory of plasticity, Wiley, New York.
Matsuda, A.(1999). “Three-dimensional finite element analysis of laminated rubber bearings using the selective integration method.” JSME Int. J., Ser. A, 42(1), 40–48.
Matsuda, A. (2001). “Evaluation for mechanical properties of laminated rubber bearings using nonlinear finite element analysis with hyperelasticity.” PhD dissertation, Tsukuba Univ., Japan (in Japanese).
Nishimura, S., Ono, K., and Ikeuchi, T.(1995). “Constitutive equation for steel under cyclic loading based on the monotonic loading.” J. Struct. Mech. Earthquake Eng., JSCE, 513/I-31, 27–38 (in Japanese).
Reicha, C. (1964). “Design of elastomer bearings.” PCI J., October, 62–78.
Research Group of Rubber Vibration Isolators. (1998). Rubber vibration isolators. Japan Railway Association, Gendaikougaku-sha, Tokyo (in Japanese).
Richard, H. (1987). Elementary applied partial differential equations, 2nd Ed., Prentice-Hall, Englewood Cliffs, N.J.
Salomon, M., Oller, S., and Barbat, A.(1999). “Finite element analysis of base isolated buildings subjected to earthquake loads.” Int. J. Numer. Methods Eng., 46(10), 1741–1761.
Seki, W., Fukahori, Y., Iseda, Y., and Matsunaga, T. (1987). “A large deformation finite element analysis for multilayer elastomeric bearings.” Transaction of the Meeting of the Rubber Division, 856–870.
Simo, J. C.(1987). “On a fully three-dimensional finite-strain viscoelastic damage model: Formulation and computational aspect.” Comput. Methods Appl. Mech. Eng., 60, 153–173.
Simo, J. C., and Hughes, T. J. R. (1997). Interdisciplinary applied mathematics Volume 7, Computational inelasticity, Springer, New York.
Simo, J. C., and Taylor, R. L.(1991). “Quasi-Incompressible Finite Elasticity in Principal Stretches. Continuum Basis and Numerical Algorithms.” Comput. Methods Appl. Mech. Eng., 85, 273–310.
Skinner, R. I., Robinson, H. W., and McVerry, H. G. (1993). An introduction to seismic isolation, Wiley, Chichester, England.
Steel Structure Committee. (2000). “Dynamic analysis of the bridge system and its performance for earthquake resistance.” Technical Rep. of JSCE, Japan (in Japanese).
Sussman, T., and Bathe, K. J.(1987). “A finite element formulation for nonlinear incompressible elastic and inelastic analysis.” Comput. Struct., 26(1/2), 357–409.
Takayama, M., Tada, H., and Tanaka, R. (1990). “Finite element analysis of laminated rubber bearing used in base-isolation system.” Transaction of the Meeting of the Rubber Division, American Chemical Society, Washington, D.C., 46–62.
Watanabe, H. (1995). “Mixed finite element methods for incompressible hyperelastic materials.” PhD dissertation, Univ. of Tokyo, Tokyo (in Japanese).
Watanabe, H., and Hisada, T.(1996). “Mixed finite element analysis of incompressible hyperelastic materials.” Theor. Appl. Mech., 45, 3–8.
Yoshida, J., Abe, M., and Fujino, Y.(2004). “Constitutive model of high-damping rubber materials.” J. Eng. Mech., 130(2), 129–141.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 American Society of Civil Engineers.
History
Received: Sep 25, 2002
Accepted: Jun 2, 2003
Published online: Apr 15, 2004
Published in print: May 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.