Energy Balance Assessment of Base-Isolated Structures
Publication: Journal of Engineering Mechanics
Volume 130, Issue 3
Abstract
This paper explores the use of energy concepts in the analysis of base-isolated structures subject to severe earthquake ground motions. We formulate the energy balance equations in moving- and fixed-base coordinate frames and provide new physical insight into the time-dependent behavior of individual terms. Conventional wisdom in earthquake engineering circles is that systems with base isolation devices should be economically competitive and designed to: (1) minimize input energy, and (2) maximize the percentage of input energy dissipated by damping and inelastic mechanisms. Through the nonlinear time-history analysis of a base-isolated mass-spring system subject to an ensemble of severe ground motion inputs, we demonstrate that improvements in objective (2) often need to be balanced against increases in input energy. Hence, by itself, objective (1) presents an overly simplified view of desirable behavior.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Association of State Highway and Transportation Officials (AASHTO). (1991). Guide specifications for seismic design, Washington, D.C.
Andriono, T., and Carr, A. J.(1991a). “Reduction and distribution of lateral seismic forces on base isolated multi-story structures.” Bull. New Zealand National Soc. Earthquake Eng.,24(3), 225–237.
Andriono, T., and Carr, A. J.(1991b). “A simplified earthquake resistant design method for base isolated multi-story buildings.” Bull. New Zealand National Soc. Earthquake Eng.,24(3), 238–250.
Arias, A. (1970). A measure of earthquake intensity, in seismic design for nuclear power plants, R. Hansen, ed., Massachusetts Institute of Technology Press, Cambridge, Mass.
Austin, M. A., Chen, X. G., and Lin, W. J. (1995). “Aladdin: A computational toolkit for interactive engineering matrix and finite element analysis.” Technical Research Rep. TR 95-74, Institute for Systems Research, University of Maryland, College Park, Md.
Austin, M. A., Lin, W. J., and Chen, X. G.(2000). “Structural matrix computations with units.” J. Comput. Civ. Eng., 14(3), 174–182.
Austin, M. A., Pister, K. S., and Mahin, S. A.(1987a). “Probabilistic design of earthquake-resistant structures.” J. Struct. Eng., 113(8), 1642–1659.
Austin, M. A., Pister, K. S., and Mahin, S. A.(1987b). “Probabilistic design of moment-resistant frames under seismic loading.” J. Struct. Eng., 113(8), 1660–1677.
Bathe, K. J. (1982). Finite element procedures in engineering analysis, Prentice-Hall, Englewood Cliffs, N.J.
Fajfar, P.(1992). “Equivalent ductility factors, taking into account low-cycle fatigue.” Earthquake Eng. Struct. Dyn., 21, 837–848.
Ghobarah, A., and Ali, H. M.(1990). “Seismic design of base-isolated highway bridges utilizing lead-rubber bearings.” Can. J. Civ. Eng., 17, 413–422.
Housner, G. W. (1956). “Limit design of structures to resist earthquakes.” Proc., World Conf. on Earthquake Engineering, Earthquake Engineering Research Center, Berkeley, Calif.
Housner, G. W.(1959). “Behavior of structures during earthquakes.” J. Struct. Div. ASCE, 85(4), 109–124.
International Conference of Building Officials (ICBO). (1997). Earthquake regulations for seismic-isolated structures: Appendix Chapter 16, Whittier, Calif.
Mayes, R. L., Buckle, I. G., Kelly, T. R., and Jones, L.(1992). “AASHTO seismic isolation design requirements for highway bridges.” J. Struct. Eng., 118(1), 284–304.
Newmark, N. M.(1959). “A method of computation for structural dynamics.” J. Eng. Mech. Div., Am. Soc. Civ. Eng., 85, 67–94.
Powell, G. H., and Allahabadi, R.(1988). “Seismic damage prediction bydeterministic methods: Concepts and procedures.” Earthquake Eng. Struct. Dyn., 16, 719–734.
Skinner, R. I., Beck, J. L., and Bycroft, G. N.(1975). “A practical system for isolating structures from earthquake attack.” Earthquake Eng. Struct. Dyn., 3, 297–309.
Structural Engineers Association of California (SEAOC). (1995). Vision 2000 Committee—Performance Based Seismic Engineering of Buildings, Volume 1: Interim Recommendations and Conceptual Framework, Sacramento, Calif.
Takewaki, I. (2000). Dynamic structural design: An inverse approach, WIT.
Turkington, D. H., Carr, A. J., Cooke, N., and Moss, P. J.(1989a). “Seismic design of bridges on lead-rubber bearings.” J. Struct. Eng., 115(12), 3000–3016.
Turkington, D. H., Carr, A. J., Cooke, N., and Moss, P. J.(1989b). “Design method for bridges on lead-rubber bearings.” J. Struct. Eng., 115(12), 3017–3030.
Uang, C. M., and Bertero, V. V.(1990). “Evaluation of seismic energy in structures.” Earthquake Eng. Struct. Dyn., 19, 77–90.
Veletsos, A. S. (1980). “Need for simple approaches in structural dynamics.” State of the Art in Earthquake Engineering 1981, Prepared for the Occasion of the 7th WCEE in Istanbul, Turkey, 258–259.
Zahrah, T. F., and Hall, W. J. (1982). “Seismic energy absorption in simple structures.” Structural Research Series No. 501, Univ. of Illinois, Urbana, Ill.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 American Society of Civil Engineers.
History
Received: Jul 13, 2000
Accepted: Mar 12, 2003
Published online: Feb 19, 2004
Published in print: Mar 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.