Interface Behavior in Steel Fiber/Cement Composites under Tension
Publication: Journal of Engineering Mechanics
Volume 124, Issue 9
Abstract
The fundamental properties of fiber-matrix interface are commonly determined by analyzing fiber pullout tests. Recognition of the dependence of the interface properties on the explanation of the pullout force-displacement curve has motivated a recent study on using special techniques to directly measure parameters relating to interface properties. In this paper, laser Moire interferometry was employed to study interface shear stress and interface energy release rate in continuous steel fiber-reinforced cementitious composites under tension in order to evaluate the fiber-matrix interface response, which was primarily acquired from fiber pullout tests. It was observed that the maximum interface shear stress in the debonded zone was independent of fiber volume fraction, fiber diameter, and applied tensile load. The interface frictional shear stress decreased with increasing slip. The interface strain energy release rate measured using the continuous fibers was larger than those obtained from short fiber pullout tests. The values of the interface energy release were dependent on fiber volume fraction and diameter. This dependency can be well described by an R-curve approach.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Bentur, A., et al. (1996). “Fiber-matrix interface.”High performance fiber reinforced cement composites 2 (HPRFCC2), A. E. Naaman and H. W. Reinhardt, eds., E & FN Spon, London, U.K., 149–192.
2.
Kawamura, M., and Igarash, S.(1992). “Fracture toughness for steel fiber-cement paste interfacial zone.”J. Mat. in Civ. Engrg., ASCE, 4(3), 227–239.
3.
Kerans, R. J., and Parthasarathy, T. A.(1991). “Theoretical analysis of the fiber pullout and pushout tests.”J. Am. Ceramic Soc., 74(7), 1585–1596.
4.
Leung, K. Y., and Li, V. C.(1990). “Strength-based and fracture-based approaches in the analysis of fiber debonding.”J. Mat. Sci. Lett., 9(10), 1140–1142.
5.
Li, Z., Mobasher, B., and Shah, S. P.(1991). “Characterization of interfacial properties in fiber-reinforced cementitious composites.”J. Am. Ceramic Soc., 74, 2156–2164.
6.
Nammur, G., and Naaman, A. E.(1989). “Bond stress model for fiber reinforced concrete based on bond stress-slip relationship.”ACI Mat. J., 86, 45–57.
7.
Ouyang, C., Pacios, A., and Shah, S. P.(1994). “Pullout of inclined fibers from cementitious matrix.”J. Engrg. Mech., ASCE, 120(12), 2641–2649.
8.
Ouyang, C., and Shah, S. P.(1991). “Geometry-dependent R-curve for quasi-brittle materials.”J. Am. Ceramic Soc., 74(11), 2831–2836.
9.
Post, D., Han, B., and Ifju, P. (1994). High sensitivity Moire. Springer-Verlag, New York, N.Y.
10.
Shah, S. P., and Ouyang, C. (1991). “Mechanical behavior of fiber-reinforced cement-based materials.”J. Am. Ceramic Soc., 74(11), 2727–2738 and 2947–2953.
11.
Shah, S. P., Swartz, S. E., and Ouyang, C. (1995). Fracture mechanics of concrete. John Wiley & Sons, Inc., New York, N.Y.
12.
Shao, Y., Li, Z., and Shah, S. P.(1993). “Matrix cracking and interface debonding in fiber-reinforced cement-matrix composites.”Advanced cement based mat., 1(2), 55–66.
13.
Stang, H., Li, Z., and Shah, S. P.(1990). “Pullout problem: stress versus fracture mechanical approach.”J. Engrg. Mech., ASCE, 116(10), 2136–2150.
14.
Stang, H., and Shah, S. P.(1986). “Failure of fiber-reinforced composites by pullout fracture.”J. Mat. Sci., 21, 953–957.
Information & Authors
Information
Published In
Copyright
Copyright © 1998 American Society of Civil Engineers.
History
Published online: Sep 1, 1998
Published in print: Sep 1998
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.