CFD Modeling of a Storm-Water Hydrodynamic Separator
Publication: Journal of Environmental Engineering
Volume 135, Issue 4
Abstract
Proliferation of manufactured unit operations to separate particulate matter (PM) transported in storm water has generated interest in modeling of such units beyond conventional “% removal” and “black-box” type evaluations. One such unit operation is a screened hydrodynamic separator (HS) combining settling and to a lesser extent inertial separation by means of an annular static screen. However, performance and mechanistic evaluations of HS units are challenged by loadings with wide PM particle size distributions (PSDs) at a range of flow rates. Wastewater-based methods such as total suspended solids (TSS) and auto samplers further challenge such evaluations. This study utilized computational fluid dynamics (CFD) to model PM separation by a HS coupled with measured PSDs, flow rates [1–125% of hydraulic capacity ], and head loss through pilot-scale testing with representative sampling and material balances. The static screen was modeled as porous cylinder, a model accounted for flow turbulence, a Lagrangian discrete phase model examined PM fate, and the resulting CFD model was stable and grid independent. CFD results were validated with pilot-scale data across the flow range with a relative percent difference between model and measured data of less than 10%. For analysis or design, CFD facilitates a spatially distributed examination of PM fate as a function of PSD and flow rate. CFD results are contrasted to conventional methods with PM as a lumped gravimetric index (TSS) and HS as a lumped overflow rate type of best management practice.
Get full access to this article
View all available purchase options and get full access to this article.
References
Andoh, R. Y. G., and Saul, A. J. (2003). “The use of hydrodynamic vortex separators and screening systems to improve water quality.” Water Sci. Technol., 47(4), 175–183.
ASTM. (1993). “Standard practice for dry preparation of soil samples for particle-size analysis and determination of soil constants.” ASTM, D42-85, Philadelphia.
Barth, T. J., and Jespersen, D. (1989). “The design and application of upwind schemes on unstructured meshes.” Technical Rep. No. AIAA-89-0366, AIAA 27th Aerospace Sciences Meeting, AIAA, Reston, Va.
Batchelor, G. K. (2000). An introduction to fluid dynamics, Cambridge University Press, Cambridge, U.K.
Brennen, C. (2005). Fundamentals of multiphase flow, 1st Ed., Cambridge University Press, New York, 1–29.
Brombach, H. (1987). “Liquid-solid separation at vortex-storm-overflows.” Proc., 4th Int. Conf. on Urban Storm Drainage (ICUD), IWA, Lausanne, Switzerland, 103–108.
Brombach, H., Xanthopoulos, C., and Pisano, H. H. (1993). “Experience with vortex separators for combined sewer overflow control.” Water Sci. Technol., 27(5–6), 93–104.
Cristina, C., Tramonte, J., and Sansalone, J. J. (2002). “A process design selection methodology for separation of traffic-generated sediments in snowmelt runoff.” Water, Air, Soil Pollut., 136(5), 33–53.
Curtis, J. S., and van Wachem, B. (2004). “Modeling particle-laden flows: A research outlook.” AIChE J., 50, 2638–2645.
Elgobashi, S. E. (1991). “Particle laden turbulent flows: Direct simulation and closure models.” Appl. Sci. Res., 48, 301–314.
Faram, M. G., and Harwood, R. (2003). “A method for the numerical assessment of sediment interceptors.” Water Sci. Technol., 47(4), 167–174.
Fenner, R. A. (1998). “Physical modeling of hydrodynamic vortex separators operating with underflow.” J. Environ. Eng., 124(9), 881–886.
Fenner, R. A., and Tyack, J. N. (1997). “Scaling laws for hydrodynamic vortex separators.” J. Environ. Eng., 123(10), 1019–1026.
Ferziger, J. J., and Peric, M. (2002). Computational methods for fluid dynamics, 3rd Ed., Springer, Berlin.
Fluent 6.2 user’s manual. (2005). Fluent Inc., Lebanon, N.H.
Huber, W. C., and Dickinson, R. E. (1988). Storm water management model user’s manual, Version 4, EPA/600/3-88/001a (NTIS PB88-236641/AS), U.S. EPA, Athens, Ga.
Igloria, R. A., Hathhorn, W. E., and Yonge, D. R. (1997). “NOM and trace metal attenuation during storm water infiltration.” J. Hydrol. Eng., 2(3), 120–127.
Issa, R. I. (1986). “Solution of implicitly discretized fluid flow equations by operator splitting.” J. Comput. Phys., 62, 40–65.
Kim, J.-Y., Ma, J., Pathapati, S., and Sansalone, J. (2004). “Continuous deflective separation of non-colloidal particulate matter in rainfall-runoff.” Proc., StormCon—3rd Annual North American Surface Water Quality Conf. & Exposition, Forrester, Palm Desert, Calif.
Kim, J.-Y., and Sansalone, J. (2008). “Event-based size distributions of particulate matter transported during urban rainfall-runoff events.” Water Res., in press.
Launder, B. E., and Spalding, D. B. (1974). “The numerical computation of turbulent flows.” Comput. Methods Appl. Mech. Eng., 3, 269–289.
Lee, J. H., and Bang, K. W. (2000). “Characterization of urban stormwater runoff.” Water Res., 34(6), 1773–1780.
Lim, M. T. N., Lam, S. W., Amal, R., Cathers, B., and Pinson, D. (2002). “Computational and experimental studies of floc behavior in a vortex separator.” Proc., 9th Int. Conf. on Urban Drainage (ICUD), IWA, Portland, Ore., 303.
Mohammadi, B., and Pironneau, O. (1994). Analysis of the k-epsilon turbulence model, Wiley, New York.
Morsi, S. A., and Alexander, A. J. (1972). “An investigation of particle trajectories in two-phase flow systems.” J. Fluid Mech., 55(2), 193–208.
Nowakowski, A. F., Cullivan, J. C., Williams, R. A., and Dyakowski, T. (2004). “Application of CFD to modeling of the flow in hydrocyclones—Is this a realizable option or still a research challenge?” Minerals Eng., 17, 661–669.
Patankar, S. (1980). Numerical heat transfer and fluid flow, 1st Ed., Hemisphere, Bristol, Pa., 126–131.
Paul, T. C., Sayal, S. K., Sakhuja, V. S., and Dhillon, G. S. (1991). “Vortex-settling basin design considerations.” J. Hydraul. Eng., 117(2), 172–189.
Petty, C. A., and Parks, S. M. (2001). “Flow predictions within hydrocyclones.” Filtr. Sep., 38(6), 28–34.
Pisano, W. C., and Brombach, H. (1994). “Operational experience with vortex solids separators for combined sewer overflow (CSO) control.” Water Sci. Technol., 29, 1–2.
Qi, D., and Lin, W. (2006). “TGrid: A new grid environment.” Proc., 1st Int. Multi-Symp. on Computer and Computational Sciences Conf. (IMSCCS’06), IMSCCS, Hangzhou, People’s Republic of China, 611–618.
Ranade, V. V. (2002). Computational flow modeling for chemical reactor engineering, 1st Ed., Academic, London.
Rossman, L. A. (2007). Stormwater management model users’ manual, Version 5.0, USEPA/600/R-05/040, USEPA, Cincinnati.
Rushton, B. (2004). “Broadway outfall stormwater retrofit incorporating a CDS unit.” Proc., World Water and Environmental Resources Congress, ASCE, Reston, Va.
Rushton, B. (2006). “Broadway outfall stormwater retrofit project (Phase II—Monitoring CDS unit and constructed pond).” Draft Rep. to EPA and Southwest Florida Water Management District (SFWMD), Southwest Florida Water Management District, Brooksville, Fla., 124.
Sansalone, J. J. (2005). “Perspective on the synthesis of unit operations and process (UOP) concepts with hydrologic controls for rainfall-runoff.” J. Environ. Eng., 131(7), 995–997.
Sansalone, J. J., and Buchberger, S. G. (1997). “Partitioning and first flush of metals in urban storm water.” J. Environ. Eng., 123(2), 134–143.
Sansalone, J. J., Hird, J. P., Cartledge, F. K., and Tittlebaum, M. E. (2005). “Event-based stormwater quality and quantity loadings from elevated urban infrastructure affected by transportation.” Water Environ. Res., 77(4), 348–365.
Sansalone, J. J., and Kim, J. Y. (2007). “Suspended particle destabilization in retained urban stormwater as a function of coagulant dosage and redox conditions.” Water Res., in press.
Sansalone, J. J., Koran, J. M., Smithson, J. A., and Buchberger, S. G. (1998). “Physical characteristics of urban roadway solids transported during rain events.” J. Environ. Eng., 124(5), 427–440.
Statie, E. C., Salcudean, M. E., and Gartshore, I. S. (2001). “The influence of hydrocyclone geometry on separation and fibre classification.” Filtr. Sep., 38(6), 36–41.
Stenstrom, M. K., and Lau, S.-L. (1998). “Oil and grease removal by floating sorbent in a CDS device.” Technical Rep., Dept. of Civil Engineering, UCLA, Los Angeles.
Tyack, J. N., and Fenner, R. A. (1999). “Computational fluid dynamics modeling of velocity profiles within a hydrodynamic separator.” Water Sci. Technol., 39(9), 169–176.
USEPA. (1999). “Stormwater technology fact sheet—Hydrodynamic vortex separators.” EPA 832-F-99-017, Washington, D.C.
USEPA. (2000). “Water quality assessment database 2000 305(b).” ⟨http://oaspub.epa.gov/waters/w305breport.nation⟩.
Vandoormaal, J. P., and Raithby, G. D. (1984). “Enhancements of the SIMPLE method for predicting incompressible fluid flows.” Numer. Heat Transfer, 7, 147–163.
Van Wachem, B. G. M., and Almstedt, A. E. (2003). “Methods for multiphase computational fluid dynamics.” Chem. Eng. J., 96, 81–98.
Versteeg, H., and Malalasekera, W. (1995). An introduction to computational fluid dynamics: The finite volume method approach, 1st Ed., Prentice-Hall, London.
Weib, G. (1997). “Vortex separator—Proposal of a dimensioning method.” Water Sci. Technol., 36(8–9), 201–206.
Information & Authors
Information
Published In
Journal of Environmental Engineering
Volume 135 • Issue 4 • April 2009
Pages: 191 - 202
Copyright
© 2009 ASCE.
History
Received: Oct 19, 2007
Accepted: Dec 9, 2008
Published online: Apr 1, 2009
Published in print: Apr 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.