Journal of Bridge Engineering

Energy dissipation bearing (EDB) is a conventional steel bridge bearing in connection with well designed mild steel dampers. Seismic performance test was undertaken for both damper units and a prototype bearing, and the results show very stable and high dissipation characteristics. In describing the hysteretic behavior of EDBs, the Wen model is proved to be more reasonable, and the corresponding model parameters are also proposed according to the test results. EDBs have been applied in the seismic control of a long span bridge, the Nanjing Jia River Bridge, for the first time, in both the longitudinal and transverse directions. Sensitivity studies were conducted to investigate the effectiveness and to determine the optimum parameters and distribution of the EDBs through nonlinear time-history analysis. The results show that EDBs achieve a very high effectiveness in seismic control, in both the longitudinal and transverse directions. Compared with other damping devices, they can provide a simple but valid seismic control solution, with low maintenance requirements, especially in the transverse direction.

The XY-friction pendulum (XY-FP) bearing is a modified friction pendulum that consists of two perpendicular steel rails with opposing concave surfaces and a connector. The connector resists tensile forces, allows independent sliding in the two orthogonal directions and enables small relative rotation of the rails about a vertical axis. Theoretical analyses were undertaken to study applications of XY-FP bearings to bridges. Two of the key features of the XY-FP bearing for the seismic isolation of bridges are: (1) resistance to tensile axial loads and (2) opportunity to provide a different period of isolation in each principal direction of the isolated structure. Numerical analyses on an XY-FP isolated bridge with different isolation periods in the principal directions subjected to near-field ground motions demonstrated the effectiveness of XY-FP bearings. Furthermore, numerical analyses that investigated the sensitivity of XY-FP isolation system response to differences in the coefficients of friction of the bearings demonstrated that bounding analysis using upper and lower estimates of the coefficients of friction will generally provide conservative estimates of displacements and shear forces for isolation systems with nonuniform isolator properties.

Aerostatic stability of super long-span bridges is a much concerned issue during the design stage. Typical aerostatic instability is the so-called torsional divergence which may lead to abrupt structural failure. The iterative static-based FEM, which generally entails the assumption of smooth oncoming flow, has been widely used to evaluate the aerostatic stability of the bridge concerned. However, the wind in atmospheric boundary layer is naturally turbulent and the effect of turbulence on bridge torsional divergence should be therefore considered, and that is the main concern of the present study. To take into account the effects of turbulence on torsional divergence, a dynamic-based time domain finite-element (FE) procedure for predicting bridge aerostatic stability is introduced first. Then the quasi-steady wind loads expressions are presented and discussed, into which the aerodynamic torsional stiffness, which is indispensable for the evaluation of aerostatic stability, has been demonstrated to be incorporated indirectly by a frequency-domain-based approach. Finally, the aerostatic performances of the longest suspension bridge in China are investigated, of which the torsional divergence is the primary concern. Numerical results show that the torsional divergence pattern in turbulent flow differs considerably from that in smooth flow. The primary difference is, while the torsional instability in smooth flow manifests as an abrupt mounting up of the twist deformation of the main girder with the increasing of the wind velocity, that in turbulent flow manifests as an unstable stochastic vibration with large peak values. Another difference is that the wind velocity for divergence in turbulent flow is obviously lower than that in smooth wind and there does not present an obvious wind velocity threshold for divergence, which is distinguished from the torsional divergence in smooth flow characterized by a clear threshold. Based on the presented time domain FE analysis procedure, the influence of turbulence intensity and gusts spatial correlation upon torsional divergence is also investigated and shown to play an important role on the aerostatic stability.

This work describes some of the most important results of the experimental and numerical analyses of Escaleritas Viaduct, Spain. Before the inauguration of this composite cable-stayed bridge in 2006, the bridge authority required a dynamic load test identifying, for instance, the natural vibration modes, the dynamic magnification factor, and the maximum vertical acceleration. The dynamic test was accompanied by numerical simulation performed in two different three-dimensional finite-element models, one of them composed of 145,000 shell elements. The correlation of test and analysis data is good and allows several interesting general conclusions to be drawn. It is shown that Escaleritas Viaduct complies with the requirements on the dynamic structural behavior defined in the standards.

Prior studies on the time-of-flight diffraction (TOFD) method have focused primarily on ground smooth, clean surfaces of steel. In practice, however, the surface of an existing bridge element will be covered with rust or have several layers of paint. The main objective of this study was to evaluate the influence of the surface condition of steel elements (i.e., painted or rusted) on the ability of the method to accurately detect and size flaws. These objectives were met by performing a number of tests on plates with saw cuts or implanted fatigue cracks with different surface conditions. These included ground smooth and polished, rusted, and painted surfaces. The data show that rusted surfaces will reduce the amplitude of the ultrasonic signals, but they will not impair the ability of the TOFD method to detect and accurately size flaws. A painted surface will also cause a reduction in signal amplitude. More important, however, is the appearance of additional wave signals that could be interpreted as false indications. While these additional signals do not obscure the presence of actual flaws or affect the accuracy of the TOFD method to size the flaws, they make flaw detection more difficult. Based on the results of this study, recommendations for field inspection on rusted or painted surfaces using the TOFD method are provided.

This paper presents the results from a study on the deterioration patterns of highway bridges, using estimated sojourn times of bridge components in various deterioration states (condition). With emphasis on the age that the bridge leaves a specified threshold condition state, the uncertainties in the estimated times are best fitted as Weibull probability distribution functions. Using both complete observations’ data and the right-censored data from a 13-year span condition historical data for the bridges, the maximum likelihood estimates are obtained for parameters of the fitted distributions, and reliability analyses are conducted for the various categories of bridges, by the type of roadways carried (interstate, noninterstate, and local roads), and the material type, i.e., cast-in-place concrete decks; prestressed concrete superstructures; steel superstructures, etc. The survival and hazard functions are developed and interpreted, including a combination of the deterioration hazard functions with the hazard functions of the effects of hurricane winds. It was observed that all the bridge categories deteriorated faster with age (nonexponential times), and bridge components located on the interstate roadways are deteriorating faster than similar bridges on noninterstate roadways. Asset worth of bridges are indicated, based on the reliability estimates.

The sandwich plate system (SPS) is a relatively new bridge deck system that consists of steel face plates bonded to a rigid polyurethane core. The decks are thin, lightweight, and modular in design and can be tailored to numerous applications. This system provides an excellent alternative for the rapid construction and rehabilitation of bridge decks. With any new system, there exists some uncertainty in the design procedures as a result of the limited population for comparison. This paper presents the results of a finite-element parametric investigation of the lateral load distribution characteristics of SPS bridges. The parametric study primarily focuses on the influence of deck thickness on distribution behavior as compared to conventional reinforced concrete decks. Results from the study demonstrate that the inherent flexibility of a thin SPS deck yields larger distribution factors (up to 20%) than a typical reinforced concrete deck, but these distribution factors can still be conservatively estimated with current AASHTO LRFD methods. Additional comparisons indicate that the distribution behavior of SPS bridges can also be estimated with the equations proposed by the NCHRP 12-62 project.

With the public’s demands for reduced construction time and traveling delays, full-depth precast bridge decks or decked bulb tees are being more widely used. When these systems are used, precast elements are brought to the construction site ready to be set in place and quickly joined together. Then, a concrete closure pour (CP) completes the connection. The selection of CP materials is critical. The procedure and methods for selecting durable CP materials are discussed in this paper. The accelerated construction is quantified as two categories: overnight cure of CP materials and 7-day cure of CP materials. For both categories, candidate materials are selected first based on literature review of published data as well as tests of compressive strength and flow and workability. Then, the performance criteria for selecting durable CP materials for both categories are developed based on durability tests of selected candidate materials. These durability tests include freezing-and-thawing durability, shrinkage, bond, and permeability tests.

Numerical and experimental studies were performed to assess the transient impact response of 11 T-beams with various dimensions and aspect ratios. Numerical modeling was performed using a three stage finite-element modeling procedure which included modal analysis, resonant analysis, and three-dimensional transient dynamic analysis. The response at impact locations on both the top centerline of the flange and the bottom centerline of the web was investigated. Physical models of three of the beams were constructed in the laboratory to determine the physical response of the beams when subjected to a transient impact and to verify the numerical results. Relationships between the fundamental frequencies and the frequencies of higher cross-sectional modes of vibration were established for the various aspect ratios. Shape factors were derived from the numerical and experimental results. The practical significance of the results is demonstrated for a project where impact-echo testing was used to nondestructively assess the condition of a decommissioned concrete T-shaped girder.

One of the promising systems for accelerated bridge construction is the use of the decked precast prestressed concrete girders or decked bulb-tee girders for the bridge superstructure. Using the calibrated three-dimensional finite-element models through field tests, a parametric study was conducted to determine the effect of intermediate diaphragms on the deflections and flexural strains of girders at the midspan as well as the live load forces in the longitudinal joint. The following diaphragm details were considered: different diaphragm types (steel and concrete), different diaphragm numbers between two adjacent girders, and different cross-sectional areas for steel diaphragms. Five bridge models with different diaphragm details were developed, and the short span length effect on the bridge behavior was also studied. It was found that as long as one intermediate diaphragm was provided between two adjacent girders at midspan, changing the diaphragm details did not affect the girder deflection, the girder strain, and the live load forces in the longitudinal joint significantly. The effect of diaphragms on the midspan deflection was more prominent in the short span bridge; however, the reduction in the maximum bending moment by the diaphragms was more significant in the long span bridge than in the short span bridge. Specific design recommendation is provided in this paper.

Deck patching is a common practice used when bridge decks have local deterioration but do not yet warrant full replacement. Rapid setting patch materials provide a quick and economical way to patch deteriorated areas without significant lane closure time. While these materials set quickly and often achieve high early strength, their long-term performance in corrosive environments and under heavy traffic loads is sometimes poor. In addition, little guidance is provided in terms of standardized testing for these materials that addresses the key properties needed for long-term service life. This paper details a testing program that evaluates a number of deck patch materials and the development of a testing protocol for material evaluation.

Rehabilitation of the existing bridges is one of the most pressing needs in maintenance of the transportation infrastructure. As an example, more than 2,000 bridges in Kansas alone need to be replaced during the next decade. The majority of these bridges have spans of 30 m (100 ft) or less, and shallow profiles. The inverted-T (IT) bridge system has gained increasing popularity in recent years due to its lower weight and relatively larger span-to-depth ratio compared to the prestressed I-girder bridges. However, there are some limitations in replacing the existing cast in place (CIP) bridges with IT system. Implementation of posttensioning, which is the focus of this paper, is a promising solution for these limitations. This leads to a higher span-to-depth ratio and reduces potential transverse cracks in the CIP deck which is a major concern for corrosion of the reinforcement. An analytical research was conducted to identify the major parameters influencing the performance of a posttensioned IT bridge system. This was followed by a parametric study to explore the scope of these parameters and specify the design limits in terms of posttensioning stages, timing scenarios, and posttensioning forces. Concrete strength and different methods for estimating time-dependent restraining moments were addressed in this parametric study.

This paper presents the lateral load distribution of various North Atlantic Treaty Organization (NATO) wheeled military trucks on a simple-span steel I-girder bridge $\left(L=36\text{m}\right)$ . The military trucks are classified into the military load classification (MLC) system. The MLC trucks demonstrate different load configurations when compared to the standard HS20 truck in terms of wheel-line spacing, number of axles, and weight. A calibrated three-dimensional finite-element analysis is conducted to examine the MLC load effects. The applicability of the AASHTO LRFD provisions is evaluated using 72 different load models. The wheel-line spacing and weight of the MLC trucks cause different flexural behavior and load distributions of the bridge when compared to those of HS20. The current AASHTO LRFD approach to determine live load distribution factors may be reasonably applicable to the MLC trucks, including approximately 20% of conservative predictions.

The Federal Highway Administration (FHWA) mandated the use of the load and resistance factor design (LRFD) approach in the U.S. for all new bridges initiated after September 2007. This paper presents the bridge deep foundation practices established through a nationwide survey of more than 30 DOTs in 2008. Highlighted by this study are the benefits of the LRFD as well as how the flexibility of its usage is being exploited in design practice. The study collected information on current foundation practice, pile analysis and design, pile drivability, pile design verification, and quality control. Since this is the first nationwide study conducted on the LRFD topic following the FHWA mandate, the status on the implementation of LRFD for bridge foundation design was also examined. The study found that: (1) more than 50% of the responded DOTs are using the LRFD for pile design, while 30% are still in transition to the LRFD; and (2) about 30% of the DOTs, who use the LRFD for pile foundations, are using regionally calibrated resistance factors to reduce the foundation costs.

The erection of steel plate girders during the construction process of a steel bridge is a complex operation, which is often left to the contractor and/or the subcontractor to plan and execute. Rules of thumb have been developed through experience to check the lateral torsional buckling of the steel girder during erection using the maximum $L/b$ (unbraced length/compressive flange width) ratio, below which no lateral torsional buckling would occur. Although the $L/b$ ratio check has proven to be useful and convenient on-site, it is necessary to provide a more rational basis for the rules of thumb, and find the maximum $L/b$ ratios by checking the lateral torsional buckling failure of girders under erection according to the latest AASHTO LRFD code. A series of parametric studies were conducted on cantilever and simply supported girders under self-weight as well as self-weight plus wind load, in order to: (1) check the rules of thumb on $L/b$ ratios and (2) determine the effects of girder flange width, flange thickness, web depth, web thickness, and yield strength on the maximum $L/b$ ratio and girder stability during erection. From the results, rules of thumb were modified for girders with common shapes, and it was obvious that (1) self-weight plus wind load controls the girder stability during erection in most cases and (2) flange width and web depth have the most effects on the maximum $L/b$ ratio and girder stability during erection.