Experimental Validation of Piezoelectric Energy-Harvesting Device for Built Infrastructure Applications
Publication: Journal of Bridge Engineering
Volume 23, Issue 8
Abstract
Vibration energy-harvesting devices are increasingly becoming more efficient and useful. The performance of such devices for energy harvesting from vibrations of civil infrastructure can be theoretically quantified, and energy harvesting under harmonic loadings can be validated experimentally. Experimental validation of such devices for civil infrastructure applications, such as bridges, remains an important but more complex and challenging issue, in part due to the more uncertain nature of the dynamic response of structures under operational conditions and problems with access for such testing. Lack of existing experimental benchmarks is also a major obstacle behind adopting this technology for bridges. This study presents a laboratory-based experimental procedure through which a piezoelectric energy harvester was experimentally verified for rail bridges in their operational condition with trains traversing them. A general experimental arrangement required for validating a piezoelectric cantilever energy-harvesting device is presented, along with the fabrication of a prototype device and detailed experimental setup. A model bridge undergoing loadings from an international train fleet was chosen, and the acceleration response from the bridge was used as the excitation source for the energy-harvesting device. Numerically estimated performances of the energy harvester were validated by experimentation for a range of trains. The method is applicable for validating energy harvesting from arbitrary vibrations of built infrastructure within the laboratory environment without the need of scaling. The device and related experimental procedure will serve as a benchmark for similar unscaled tests within a laboratory environment and can be useful for assessing devices or their applications in monitoring built infrastructure under realistic conditions without the need for deployment on site.
Get full access to this article
View all available purchase options and get full access to this article.
References
Al-Ashtari, W., M. Hunstig, T. Hemsel, and W. Sextro. 2013. “Enhanced energy harvesting using multiple piezoelectric elements: theory and experiments.” Sens. Actuators A Phys. 200: 138–146. https://doi.org/10.1016/j.sna.2013.01.008.
Ali, S. F., M. I. Friswell, and S. Adhikari. 2011. “Analysis of energy harvesters for highway bridges.” J. Intell. Mater. Syst. Struct. 22 (16): 1929–1938. https://doi.org/10.1177/1045389X11417650.
Anton, S. R., and H. A. Sodano. 2007. “A review of power harvesting using piezoelectric materials (2003–2006).” Smart Mater. Struct. 16 (3): R1–R21. https://doi.org/10.1088/0964-1726/16/3/R01.
Cahill, P., C. Hanley, V. Jaksic, A. Mathewson, and V. Pakrashi, 2016a. “Energy harvesting for monitoring bridges over their operational life.” In Proc., 8th European Workshop on Structural Health Monitoring (EWSHM), 11. Bad Breisig, Germany: NDT.net. http://www.ndt.net/events/EWSHM2016/app/content/topic.php?eventID=34&TopicID=3190.
Cahill, P., B. Hazra, R. Karoumi, A. Mathewson, and V. Pakrashi. 2018. “Vibration energy harvesting based monitoring of an operational bridge undergoing forced vibration and train passage.” Mech. Syst. Signal Process. 106, 265–283. https://doi.org/10.1016/j.ymssp.2018.01.007.
Cahill, P., V. Jaksic, J. Keane, A. O’Sullivan, A. Mathewson, S. F. Ali, and V. Pakrashi. 2016b. “Effect of road surface, vehicle, and device characteristics on energy harvesting from bridge–vehicle interactions.” Comput.-Aided Civ. Infrastruct. Eng. 31 (12): 921–935. https://doi.org/10.1111/mice.12228.
Cahill, P., N. A. N. Nuallain, N. Jackson, A. Mathewson, R. Karoumi, and V. Pakrashi. 2014a. “Energy harvesting from train-induced response in bridges.” J. Bridge Eng. 19 (9): 04014034. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000608.
Cahill, P., R. O'Keeffe, N. Jackson, A. Mathewson, and P. Pakrashi. 2014b. “Structural health monitoring of reinforced concrete beam using piezoelectric energy harvesting system.” In Proc., 7th European Workshop on Structural Health Monitoring (EWSHM), 7. Lyon, France: Centre pour la Communication Scientifique Directe (CCSD). https://hal.inria.fr/EWSHM2014/hal-01020338v1.
Chong, C.-Y., and S. Kumar. 2003. “Sensor networks: Evolution, opportunities, and challenges.” Proc. IEEE. 91 (8): 1247–1256. https://doi.org/10.1109/JPROC.2003.814918.
DuToit, N. E., and B. L. Wardle. 2007. “Experimental verification of models for microfabricated piezoelectric vibration energy harvesters.” AIAA J. 45 (5): 1126–1137. https://doi.org/10.2514/1.25047.
Elvin, N. G., N. Lajnef, and A. A. Elvin. 2006. “Feasibility of structural monitoring with vibration powered sensors.” Smart Mater. and Struct. 15 (4): 977–986. https://doi.org/10.1088/0964-1726/15/4/011.
Erturk, A. 2011. “Piezoelectric energy harvesting for civil infrastructure system applications: Moving loads and surface strain fluctuations.” J. Intell. Mater. Syst. Struct. 22 (17): 1959–1973. https://doi.org/10.1177/1045389X11420593.
Gungor, V., and G. Hancke. 2009. “Industrial wireless sensor networks: Challenges, design principles, and technical approaches.” IEEE Trans. Ind. Electron. 56 (10): 4258–4265. https://doi.org/10.1109/TIE.2009.2015754.
IEEE (The Institute of Electrical and Electronics Engineers). 1988. Standard on piezoelectricity. ANSI/IEEE Std 176-1987. New York.
Jackson, N., L. Keeney, and A. Mathewson. 2013. “Flexible-CMOS and biocompatible piezoelectric AlN material for MEMS applications.” Smart Mater. Struct. 22 (11): 115033. https://doi.org/10.1088/0964-1726/22/11/115033.
Kaur, N., and S. Bhalla. 2016. “Numerical investigations on energy harvesting potential of thin PZT patches adhesively bonded on RC structures.” Sens. Actuators A Phys. 241, 44–59. https://doi.org/10.1016/j.sna.2016.02.002.
Kim, S.-H., J.-H. Ahn, H.-M. Chung, and H.-W. Kang. 2011. “Analysis of piezoelectric effects on various loading conditions for energy harvesting in a bridge system.” Sens. Actuators A Phys. 167 (2): 468–483. https://doi.org/10.1016/j.sna.2011.03.007.
Kołakowski, P., J. Szelążek, K. Sekuła, A. Świercz, K. Mizerski, and P. Gutkiewicz. 2011. “Structural health monitoring of a railway truss bridge using vibration-based and ultrasonic methods.” Smart Mater. Struct. 20 (3): 035016. https://doi.org/10.1088/0964-1726/20/3/035016.
Liu, H., C. Lee, T. Kobayashi, C. J. Tay, and C. Quan. 2012. “Piezoelectric MEMS-based wideband energy harvesting systems using a frequency-up-conversion cantilever stopper.” Sens. Actuators A Phys. 186: 242–248. https://doi.org/10.1016/j.sna.2012.01.033.
Pakrashi, V., J. Harkin, and J. Kelly. 2013. “Monitoring and repair of an impact damaged prestressed bridge.” Proc. Inst. Civ. Eng. Bridge Eng. 166 (1): 16–29. https://doi.org/10.1680/bren.10.00057.
Peigney, M., and D. Siegert. 2013. “Piezoelectric energy harvesting from traffic induced bridge vibrations.” Smart Mater. Struct. 22 (9): 095019. https://doi.org/10.1088/0964-1726/22/9/095019.
Priya, S. 2007. “Advances in energy harvesting using low profile piezoelectric transducers.” J. Electroceram. 19 (1): 167–184. https://doi.org/10.1007/s10832-007-9043-4.
Sazonov, E., D. Curry, and P. Pillay. 2009. “Self-powered sensors for monitoring of highway bridges.” IEEE Sens. J. 9 (11): 1422–1429. https://doi.org/10.1109/JSEN.2009.2019333.
Shaikh, F. K., and S. Zeadally. 2016. “Energy harvesting in wireless sensor networks: A comprehensive review.” Renewable Sustainable Energy Rev. 55: 1041–1054. https://doi.org/10.1016/j.rser.2015.11.010.
Wang, H., and Q. Meng. 2013. “Analytical modeling and experimental verification of vibration-based piezoelectric bimorph beam with a tip-mass for power harvesting.” Mech. Syst. Signal Process. 36 (1): 193–209. https://doi.org/10.1016/j.ymssp.2012.10.015.
Wischke, M., M. Masur, M. Kröner, and P. Woias. 2011. “Vibration harvesting in traffic tunnels to power wireless sensor nodes.” Smart Mater. Struct. 20 (8): 085014. https://doi.org/10.1088/0964-1726/20/8/085014.
Xie, X. D., N. Wu, K. V. Yuen, and Q. Wang. 2013. “Energy harvesting from high-rise buildings by a piezoelectric coupled cantilever with a proof mass.” Int. J. Eng. Sci. 72: 98–106. https://doi.org/10.1016/j.ijengsci.2013.07.004.
Žnidarič A., V. Pakrashi, A. O’Connor, and E. O’Brien. 2011. “A review of road structure data in six European countries.” Proc. Inst. Civ. Eng. Urban Des. Plann. 164 (4): 225–232. https://doi.org/10.1680/udap.900054.
Zuo, L., and X. Tang. 2013. “Large-scale vibration energy harvesting.” J. Intell. Mater. Syst. Struct. 24 (11): 1405–1430. https://doi.org/10.1177/1045389X13486707.
Information & Authors
Information
Published In
Copyright
© 2018 American Society of Civil Engineers.
History
Received: Aug 17, 2017
Accepted: Feb 6, 2018
Published online: Jun 5, 2018
Published in print: Aug 1, 2018
Discussion open until: Nov 5, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.