Regression-Based Adjustment Factor to Better Estimate Shear Capacity for Load-Rating Simple Span PC Girders
Publication: Journal of Bridge Engineering
Volume 23, Issue 5
Abstract
In this study, an adjustment factor was developed to better estimate the shear capacity of simple span prestressed concrete (PC) girders, for intended use in load rating. The adjustment factor is expressed as a function of several critical girder parameters including concrete strength, prestress level, stirrup spacing, and girder height. The adjustment factor was determined from a regression analysis of over 200 shear capacity results. The database was obtained from a parametric analysis conducted with a finite-element model validated with experimental data. Three different code methods were considered for comparison. Generally, code results were found to be inconsistently conservative. Application of the adjustment factor to an established procedure produced improvement in the accuracy and consistency of shear capacity estimation over existing code methods for the range of girder parameters considered. In addition, potential effects on rating factors for inventory and operational levels were quantified.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was partially funded by the MDOT through Grant 2010-0298-Z5. The authors would like to thank the editors and reviewers for their time and effort in reviewing the current manuscript.
References
AASHTO (1973). Standard specifications for highway bridges, 11th Ed., Washington, DC.
AASHTO (1979). Interim revisions to standard specifications for highway bridges, Washington, DC.
AASHTO (1994). LRFD bridge design specifications, 1st Ed, Washington, DC.
AASHTO (2002). Standard specifications for highway bridges, 17th Ed., Washington, DC.
AASHTO (2008). LRFD bridge design specifications, 4th Ed., Washington, DC.
AASHTO (2011). Manual for bridge evaluation, 2nd Ed., Washington, DC.
AASHTO (2014). LRFD bridge design specifications, 6th Ed., Washington, DC.
Chehab, A., Dam, T., Eamon, C. D., and Parra-Montesinos, G. (2017). “Finite element modeling of shear failure in prestressed concrete AASHTO beams.” Proc., PCI Convention and National Bridge Conf., Precast/Prestressed Concrete Institute, Chicago.
CSA (Canadian Standards Association). (2004). “Design of concrete structures.” CAN/CSA A23.3-04, Mississauga, ON, Canada.
Cumming, D. A., French, C. E., and Shield, C. K. (1998). “Shear capacity of high-strength concrete prestressed girders.” Rep. 1998-12, Minnesota DOT, St. Paul, MN, 396.
Eamon, C., Kamjoo, V., and Shinki, K. (2016). “Design live-load factor calibration for Michigan highway bridges.” J. Bridge Eng., 04016014.
Eamon, C. D., Parra-Montesinos, G., and Chehab, A. (2014). “Evaluation of prestressed concrete beams in shear.” MDOT Rep. RC-1615, Michigan DOT, Lansing, MI.
Eligehausen, R., Popov, E., and Bertero, V. (1983). “Local bond stress-slip relationship of deformed bars under generalized excitations.” Rep. No. UCB/EERC-83/23, Earthquake Engineering Center, Univ. of California, Berkeley, CA.
Esfandiari, A., and Adebar, P. (2009). “Shear strength evaluation of concrete bridge girders.” ACI Struct. J., 106(4), 416–426.
Hartmann, D. L., Breen, J. E., and Kreger, M. E. (1988). “Shear capacity of high strength prestressed concrete girders.” CTR-3-5-84-381-2, Texas Univ. at Austin, Center for Transportation Research, Austin, TX, 271.
Hawkins, N. M., and Kuchma, D. A. (2007). “Application of LRFD bridge design specifications to high-strength structural concrete: Shear provisions.” NCHRP Rep. 579, Transportation Research Board, Washington, DC.
Hawkins, N. M., Kuchma, D. A., Mast, R. F., Marsh, M. L., and Reineck, K.-H. (2005). “Simplified shear design of structural concrete.” NCHRP Rep. 549, Transportation Research Board, Washington, DC.
Hognestad, E., Hanson, N. W., and McHenry, D. (1955). “Concrete stress distribution in ultimate strength design.” ACI Struct. J., 52(4), 455–479.
Joint ASCE-ACI Committee 426. (1973). “The shear strength of reinforced concrete members—Chapters 1 to 4.” J. Struct. Div., 99(6), 1091–1187.
Kuchma, D., Kang, S. K., Nagle, T. J., and Hawkins, N. M. (2008). “Shear tests on high-strength prestressed bulb-tee girders: Strength and key observations.” ACI Structural Journal, 105(3), 358–367.
Kupfer, H., Hilsdorf, H. K., and Rusch, H. (1969). “Behavior of concrete under biaxial stresses.” ACI J. Proc., 66(8), 656–666.
Kupfer, H. B., Hilsdorf, H. K., and Rusch, H. (1973). “Behavior of concrete under biaxial stresses.” J. Eng. Mech. Div., 99(4), 853–866.
Laskar, A., Hsu, T. C., and Mo, Y. L. (2010). “Shear strengths of prestressed concrete beams, Part 1: Experiments and shear design equations.” ACI Struct. J., 107(3), 330–339.
Lee, S.-C., Cho, J.-Y., and Vecchio, F. J. (2013). “Tension-stiffening model for steel fiber-reinforced concrete containing conventional reinforcement.” ACI Struct. J., 110(4), 639.
Lin, C.-H., Chen, S.-T., and Lin, W.-C. (2012). “Shear behaviour of prestressed beams with high-workability concrete.” Mag. Concr. Res., 64(5), 419–432.
Llanos, G., Ross, B. E., and Hamilton, H. R. (2009). “Shear performance of existing prestressed concrete bridge girders.” BD545-56, Dept. of Civil and Coastal Engineering, Univ. of Florida, Gainesville, FL, 160.
Mahesh, P., and Surinder, D. (2011). “Support vector regression based shear strength modeling of deep beams.” Comput. Struct., 89(13–14), 1430–1439.
MDOT (Michigan DOT). (2009). Bridge analysis guide: 2005 ed., with 2009 interim update, parts 1 and 2. MDOT Construction and Technology Support Area, Lansing, MI.
Ning, Z., and Tan, K. H. (2007). “Direct strut-and-tie model for single span and continuous deep beams.” Eng. Struct., 29(11), 2987–3001.
Pei, J. S., Martin, R. D., Sandburg, C. J., and Kang, T. H. (2008). “Rating precast prestressed concrete bridges for shear.” FHWA-OK-08-08, Univ. of Oklahoma, Norman, OK.
Richart, F. E., Brandtzaeg, A., and Brown, R. L. (1928). “A study of the failure of concrete under combined compressive stresses.” Bulletin No.185, Univ. of Illinois Engineering Experimental Station, Urbana, Illinois, 104.
Ross, B. E., Ansley, M., and Hamilton, H. R. (2011). “Load testing of 30-year-old AASHTO Type III highway bridge girders.” PCI J., 56(4), 152–163.
Saqan, E., and Frosch, R. J. (2009). “Influence of flexural reinforcement on shear strength of prestressed concrete beams.” ACI Struct. J., 106(1), 60–68.
Scott, B. D., Park, R., and Priestley, M. J. N. (1982). “Stress-strain behavior of concrete confined by overlapping hoops at low and high strain rates.” ACI J., 79(1), 13–27.
Shahawy, M. A., and Cai, C. S. (1999). “New approach to shear design of prestressed concrete members.” PCI J., 44(4), 92–117.
Tassios, T. P., and Yannopoulos, P. J. (1981). “Analytical studies on reinforced concrete members under cyclic loading based on bond stress-slip relationships.” J. Proc., 78(3), 206–216.
Vecchio, F. (1992). “Finite element modeling of concrete expansion and confinement.” J. Struct. Eng., 2390–2406.
Vecchio, F. (2000). “Disturbed stress field model for reinforced concrete: Formulation.” J. Struct. Eng., 1070–1077.
Vecchio, F. J., and Collins, M. P. (1986). “The modified compression-field theory for reinforced concrete elements subjected to shear.” ACI J., 832(2), 219–231.
VecTor2 [Computer software]. VecTor Analysis Group, Toronto.
Walraven, J. (1981). “Fundamental analysis of aggregate interlock.” J. Struct. Div., ASCE, 107(ST11), 2245–2270.
Wang, G., and Meng, S. P. (2008). “Modified strut-and-tie model for prestressed concrete deep beams.” Eng. Struct., 30(12), 3489–3496.
Wight, J. K. (2016). Reinforced concrete: Mechanics and design, 7th Ed., Pearson, Hoboken, NJ.
Wilder, K., Lava, P., Debruyne, D., Wang, Y., De Roeck, G., and Vandewalle, L. (2015). “Stress field based truss model for shear-critical prestressed concrete girders.” Structures, 3(Aug), 28–42.
Wong, P., Vecchio, F. J., and Trommels, H. (2013). VecTor2 and FormWorks manual, 2nd Ed., Univ. of Toronto, Toronto.
Information & Authors
Information
Published In
Copyright
© 2018 American Society of Civil Engineers.
History
Received: Jun 7, 2017
Accepted: Oct 31, 2017
Published online: Feb 16, 2018
Published in print: May 1, 2018
Discussion open until: Jul 16, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.