Model Describing Material-Dependent Deformation Behavior in High-Velocity Metal Forming Processes
Publication: Journal of Engineering Mechanics
Volume 135, Issue 4
Abstract
A constitutive model for rate-dependent and thermomechanically coupled plasticity at finite strains is presented. The plasticity model is based on a model and rate-dependent behavior is included by use of a Perzyna-type formulation. Adiabatic heating effects are handled in a consistent way and not, as is a common assumption, through a constant conversion of the internal work rate into rate of heating. The conversion factor is instead derived from thermodynamic considerations. The stored energy is assumed to be a function of a single internal variable which differs from the effective plastic strain. This allows a thermodynamically consistent formulation to be obtained which, as shown, can be calibrated by use of simple procedures. Choosing 100Cr6 steel in two differently heat treated conditions as prototype material, experimental tests are performed, enabling the model to be calibrated. Significant differences in deformation behavior are noted as the differently heat treated specimens are compared. In addition, the local stress-updating procedure is reduced to a single scalar equation, permitting a very efficient numerical implementation of the model. The constitutive formulation proposed was employed in an explicit finite element solver, illustrative simulations of a high-velocity metal forming process being performed to demonstrate the capabilities of the model and certain characteristic traits of the materials that were studied.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The first two writers gratefully acknowledge the funding provided by the ProViking program Simu-Net-Shape under grant SFF V03.22.
References
Batra, R. C., and Liu, D.-S. (1990). “Adiabatic shear banding in dynamic plane strain compression of a viscoplastic material.” Int. J. Plasticity, 6, 231–246.
Batra, R. C., and Stevens, J. B. (1998). “Adiabatic shear bands in axisymmetric impact and penetration problems.” Comput. Methods Appl. Mech. Eng., 151, 325–342.
Bever, M. B., Holt, D. L., and Titchener, A. L. (1973). The stored energy of cold work, 1st Ed., Pergamon, New York.
Chrysochoos, A., Maisonneuve, O., Martin, G., Caumon, H., and Chezeaux, J. C. (1989). “Plastic and dissipated work and stored energy.” Nucl. Eng. Des., 114, 323–333.
Clifton, R. J., Duffy, J., Hartley, K. A., and Shawki, T. G. (1984). “On critical conditions for shear band formation at high strain rates.” Scr. Metall., 18, 443–448.
Cottrell, A. H. (1963). Dislocations and plastic flow in crystals, 5th Ed., Oxford University Press, New York.
Håkansson, P., Wallin, M., and Ristinmaa, M. (2005). “Comparison of isotropic hardening and kinematic hardening in thermoplasticity.” Int. J. Plasticity, 7, 1435–1460.
Hallberg, H., Håkansson, P., and Ristinmaa, M. (2007). “A constitutive model for the formation of martensite in austenitic steels under large strain plasticity.” Int. J. Plasticity, 23, 1213–1239.
Hartley, K. A., Duffy, J., and Hawley, R. H. (1987). “Measurement of the temperature profile during shear band formation in steels deforming at high strain rates.” J. Mech. Phys. Solids, 35(3), 283–301.
Heeres, O. M., Suiker, A. S. J., and de Borst, R. (2002). “A comparison between the Perzyna viscoplastic model and the consistency viscoplastic model.” Eur. J. Mech. A/Solids, 21, 1–12.
Hodowany, J., Ravichandran, G., Rosakis, A. J., and Rosakis, P. (2000). “Partition of plastic work into heat and stored energy in metals.” Exp. Mech., 40(2), 113–123.
Kapoor, R., and Nemat-Nasser, S. (1998). “Determination of temperature rise during high strain rate deformation.” Mech. Mater., 27, 1–12.
Kröner, E. (1960). “Allgemeine Kontinuumstheorie der Versetzungen und Eigenspannungen.” Arch. Ration. Mech. Anal., 4, 273–334.
Lee, E. H., and Liu, D. T. (1967). “Finite strain plasticity particularly for plane waves.” J. Appl. Phys., 38, 19–27.
Lin, R. C., and Brocks, W. (2006). “On a finite-strain viscoplastic law coupled with anisotropic damage: Theoretical formulations and numerical applications.” Arch. Appl. Mech., 75, 315–325.
Löwisch, G., and Dalgic, M. (2006). “The influence of the temperature on the stress-strain hardening curves of a bearing steel and a case hardening steel.” Materialwiss. Werkstofftech., 37(1), 134–141.
Lubliner, J. (1972). “On the thermodynamic foundation of non-linear solid mechanics.” Int. J. Non-Linear Mech., 7, 237–254.
Manjoine, M. J. (1944). “Influence of rate of strain and temperature on yield stresses of mild steel.” Trans. ASME, 66, A-211–A-218.
Mapelli, C., Venturini, R., and Boniardi, M. (2005). “Simulation and optimisation of an annealing process of sub-critical spheroidization annealing of a 100Cr6 steel.” Scand. J. Metall., 34, 192–204.
Marchand, A., and Duffy, J. (1988). “An experimental study of the formation process of adiabatic shear bands in a structural steel.” J. Mech. Phys. Solids, 36(3), 251–283.
Mason, J. J., Rosakis, A. J., and Ravichandran, G. (1994). “On the strain and strain rate dependence of the fraction of plastic work converted to heat: An experimental study using high speed infrared detectors and the Kolsky bar.” Mech. Mater., 17, 135–145.
Miller, A. (1987). Unified constitutive equations for creep and plasticity, Elsevier Applied Science, Amsterdam, The Netherlands, 139–269.
Oliferuk, W., Gadaj, S. P., and Grabski, M. W. (1985). “Energy storage during the tensile deformation of Armco iron and austenitic steel.” Mater. Sci. Eng., 70, 131–141.
Olszak, W., and Perzyna, P. (1969). “On thermal effects in viscoplasticity.” Z. Angew. Math. Phys., 20(5), 676–680.
Ottosen, N. S., and Ristinmaa, M. (2005). The mechanics of constitutive modeling, 1st Ed., Elsevier, Amsterdam, The Netherlands.
Perzyna, P. (1966). “Fundamental problems in viscoplasticity.” Adv. Appl. Mech., 9, 243–377.
Phillips, A., and Wu, H. -C. (1973). “A theory of viscoplasticity.” Int. J. Solids Struct., 9, 15–30.
Ramesh, A., Melkote, S. N., Allard, L. F., Riester, L., and Watkins, T. R. (2005). “Analysis of white layers formed in hard turning of AISI 52100 steel.” Mater. Sci. Eng., A, 390, 88–97.
Ristinmaa, M., and Ottosen, N. S. (2000). “Consequences of dynamic yield surface in viscoplasticity.” Int. J. Solids Struct., 37, 4601–4622.
Ristinmaa, M., Wallin, M., and Ottosen, N. S. (2007). “Thermodynamic format and heat generation of isotropic hardening plasticity.” Acta Mech., 194, 103–121.
Rosakis, P., Rosakis, A. J., Ravichandran, G., and Hodowany, J. (2000). “A thermodynamic internal variable model for the partition of plastic work into heat and stored energy in metals.” J. Mech. Phys. Solids, 48, 581–607.
Runesson, K., Ristinmaa, M., and Mähler, L. (1999). “A comparison of viscoplasticity formats and algorithms.” Mech. Cohesive-Frict. Mater., 4, 75–98.
Ryttberg, K. (2007). “Fracture behavior and related microstructures of tool steels parted-off at high rates of strain.” Licentiate dissertation, Dept. of Materials and Manufacturing Technology, Chalmers Univ. of Technology, Chalmers, Sweden.
Sherby, O. D., Lytton, J. L., and Dorn, J. E. (1957). “Activation energies for creep of high-purity aluminum.” Acta Metall., 5, 219–227.
Shi, J., and Liu, C. R. (2006). “On predicting chip morphology and phase transformation in hard machining.” Int. J. Adv. Manuf. Technol., 27, 645–654.
Simo, J. C. (1998). Handbook of numerical analysis, Elsevier, Amsterdam, The Netherlands, Vol. IV, 183–499.
Simo, J. C., and Hughes, T. J. R. (2000). Computational inelasticity, 2nd Ed., Springer, Berlin.
Simo, J. C., and Miehe, C. (1992). “Associative coupled thermoplasticity at finite strains: Formulation, numerical analysis and implementation.” Comput. Methods Appl. Mech. Eng., 98, 41–104.
Smallman, R. E., and Bishop, R. J. (1999). Modern physical metallurgy and materials engineering, 6th Ed., Butterworth-Heinemann, London.
Taylor, G. I., and Quinney, H. (1934). “The latent energy remaining in a metal after cold working.” Proc. R. Soc. London, A143, 307–326.
Trötzschel, J., Müller, S., Pantleon, W., and Klimanek, P. (1997). “Investigation of local strain fields during high-speed deformation.” Comput. Mater. Sci., 9, 207–217.
Tugcu, P. (1995). “Heat conduction effects on strain localization in plane-strain tension.” Int. J. Numer. Methods Eng., 38, 2083–2099.
Tugcu, P. (1996). “Thermomechanical analysis of upsetting of a cylindrical billet.” Comput. Struct., 58(1), 1–12.
Wriggers, P., Miehe, C., Kleiber, M., and Simo, J. C. (1992). “On the coupled thermomechanical treatment of necking problems via finite element methods.” Int. J. Numer. Methods Eng., 33, 869–883.
Zehnder, A. T. (1991). “A model for the heating due to plastic work.” Mech. Res. Commun., 18(1), 23–28.
Zhu, Z. G., and Batra, R. C. (1992). “Consideration of phase transformations in the study of shear bands in a dynamically loaded steel block.” Trans. ASME, J. Appl. Mech., 114, 368–377.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Dec 14, 2007
Accepted: Jul 1, 2008
Published online: Apr 1, 2009
Published in print: Apr 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.