Abstract

Lack of proper physical separation between the anodic and cathodic zones of a constructed wetland-microbial fuel cell (CW-MFC) causes higher oxygen diffusion into the anodic zone, which leads to nonproductive electron losses. In this investigation, performance of two upflow hydroponic CW-MFCs with a low-cost ceramic separator (R1) and without a separator (R2) was evaluated with Canna indica at the cathodic side. The chemical oxygen demand removal efficiencies of R1 and R2 were found to be 86.2 ± 8.1% and 91.5 ± 4.9%, respectively. However, from the polarization plots, internal resistance of R1 (240 Ω) was found to be 2.6 times lower than that of R2 (626 Ω). In addition, it was revealed that R1 (258.78 mW·m−3) exhibited almost three times higher power density than R2 (91.02 mW·m−3). The normalized energy recovery of the CW-MFC with a ceramic separator was also 2.7 times higher than that without a separator. The presence of a separator thus facilitated better anaerobicity to support substrate utilization by electrogenesis in the anodic zone of R1 and prevented oxygen diffusion, which resulted in higher energy recovery while only marginally compromising the efficiency of organic matter removal.

Get full access to this article

View all available purchase options and get full access to this article.

Acknowledgments

Imprint Initiative, Ministry of Human Resource Development (MHRD), Department of Urban Development, Government of India financially supported the research project [File No.: 41-2/2015-T.S.-I (Pt.), Dt.09-01-2016].

References

Ahilan, V., G. D. Bhowmick, M. M. Ghangrekar, M. Wilhelm, and K. Rezwan. 2019a. “Tailoring hydrophilic and porous nature of polysiloxane derived ceramer and ceramic membranes for enhanced bioelectricity generation in microbial fuel cell.” Ionics 25 (1): 1–12.
Ahilan, V., C. C. de Barros, G. D. Bhowmick, M. M. Ghangrekar, M. M. Murshed, M. Wilhelm, and K. Rezwan. 2019b. “Microbial fuel cell performance of graphitic carbon functionalized porous polysiloxane based ceramic membranes.” Bioelectrochemistry 129: 259–269.
APHA (American Public Health Association). 2005. Standard methods for the examination of water and wastewater. Washington, DC: APHA.
Armstrong, W., S. H. F. W. Justin, P. M. Beckett, and S. Lythe. 1991. “Root adaptation to soil waterlogging.” Aquat. Bot. 39 (1–2): 57–73.
Arunbabu, V., S. Sruthy, I. Antony, and E. V. Ramasamy. 2015. “Sustainable greywater management with Axonopus compressus (broadleaf carpet grass) planted in sub surface flow constructed wetlands.” J. Water Process Eng. 7: 153–160.
Bhowmick, G. D., M. T. Noori, I. Das, B. Neethu, M. M. Ghangrekar, and A. Mitra. 2018. “Bismuth doped TiO2 as an excellent photocathode catalyst to enhance the performance of microbial fuel cell.” Int. J. Hydrogen Energy 43 (15): 7501–7510.
Corbella, C., and J. Puigagut. 2016. “Microbial fuel cells implemented in constructed wetlands: Fundamentals, current research and future perspectives.” Contrib. Sci. 11: 113–120.
Das, I., M. T. Noori, G. D. Bhowmick, and M. M. Ghangrekar. 2018a. “Synthesis of bimetallic iron ferrite Co0.5Zn0.5Fe2O4 as a superior catalyst for oxygen reduction reaction to replace noble metal catalysts in microbial fuel cell.” Int. J. Hydrogen Energy 43 (41): 19196–19205.
Das, I., M. T. Noori, G. D. Bhowmick, and M. M. Ghangrekar. 2018b. “Synthesis of tungstate oxide/bismuth tungstate composite and application in microbial fuel cell as superior low-cost cathode catalyst than platinum.” J. Electrochem. Soc. 165 (13): G146–G153.
Doherty, L., X. Zhao, Y. Zhao, and W. Wang. 2015a. “The effects of electrode spacing and flow direction on the performance of microbial fuel cell-constructed wetland.” Ecol. Eng. 79: 8–14.
Doherty, L., Y. Zhao, X. Zhao, and W. Wang. 2015b. “Nutrient and organics removal from swine slurry with simultaneous electricity generation in an alum sludge-based constructed wetland incorporating microbial fuel cell technology.” Biochem. Eng. J. 266: 74–81.
Fang, Z., H.-L. Song, N. Cang, and X.-N. Li. 2013. “Performance of microbial fuel cell coupled constructed wetland system for decolorization of azo dye and bioelectricity generation.” Bioresour. Technol. 144: 165–171.
Ge, Z., J. Li, L. Xiao, Y. Tong, and Z. He. 2014. “Recovery of electrical energy in microbial fuel cells: Brief review.” Environ. Sci. Technol. Lett. 1 (2): 137–141.
Ghadge, A. N., and M. M. Ghangrekar. 2015. “Development of low cost ceramic separator using mineral cation exchanger to enhance performance of microbial fuel cells.” Electrochim. Acta 166: 320–328.
Ghangrekar, M. M., S. R. Asolekar, and S. G. Joshi. 2005. “Characteristics of sludge developed under different loading conditions during UASB reactor start-up and granulation.” Water Res. 39 (6): 1123–1133.
Ieropoulos, I. A., A. Stinchcombe, I. Gajda, S. Forbes, I. Merino-Jimenez, G. Pasternak, D. Sanchez-Herranz, and J. Greenman. 2016. “Pee power urinal—microbial fuel cell technology field trials in the context of sanitation.” Environ. Sci. Water Res. Technol. 2 (2): 336–343.
Jana, P. S., M. Behera, and M. M. Ghangrekar. 2010. “Performance comparison of up-flow microbial fuel cells fabricated using proton exchange membrane and earthen cylinder.” Int. J. Hydrogen Energy 35 (11): 5681–5686.
Knowles, P., G. Dotro, J. Nivala, and J. García. 2011. “Clogging in subsurface-flow treatment wetlands: Occurrence and contributing factors.” Ecol. Eng. 37 (2): 99–112.
Liu, S., H. Song, X. Li, and F. Yang. 2013. “Power generation enhancement by utilizing plant photosynthate in microbial fuel cell coupled constructed wetland system.” Int. J. Photoenergy 2013: 172010.
Logan, B. E. 2008. Microbial fuel cells. Hoboken, NJ: John Wiley & Sons.
Logan, B. E., B. Hamelers, R. Rozendal, U. Schröder, J. Keller, S. Freguia, P. Aelterman, W. Verstraete, and K. Rabaey. 2006. “Microbial fuel cells: Methodology and technology.” Environ. Sci. Technol. 40 (17): 5181–5192.
Mohanty, A., A. K. Yadav, and G. Roy Chaudhury. 2016. “Removal of nitrate nitrogen and chemical oxygen demand in upflow fixed bed reactor using heterotrophic microorganisms.” J. Cleaner Prod. 127: 573–578.
Neethu, B., G. D. Bhowmick, and M. M. Ghangrekar. 2018. “Enhancement of bioelectricity generation and algal productivity in microbial carbon-capture cell using low cost coconut shell as membrane separator.” Biochem. Eng. J. 133: 205–213.
Oh, S. E., J. R. Kim, J.-H. Joo, and B. E. Logan. 2009. “Effects of applied voltages and dissolved oxygen on sustained power generation by microbial fuel cells.” Water Sci. Technol. 60 (5): 1311–1317.
Oh, S. E., S. Van Ginkel, and B. E. Logan. 2003. “The relative effectiveness of pH control and heat treatment for enhancing biohydrogen gas production.” J. Am. Chem. 37 (22): 5186–5190.
Oon, Y.-L., S.-A. Ong, L.-N. Ho, Y.-S. Wong, Y.-S. Oon, H.-K. Lehl, and W.-E. Thung. 2015. “Hybrid system up-flow constructed wetland integrated with microbial fuel cell for simultaneous wastewater treatment and electricity generation.” Bioresour. Technol. 186: 270–275.
Pedescoll, A., A. Corzo, E. Álvarez, J. García, and J. Puigagut. 2011. “The effect of primary treatment and flow regime on clogging development in horizontal subsurface flow constructed wetlands: An experimental evaluation.” Water Res. 45 (12): 3579–3589.
Potter, M. C. 1911. “Electrical effects accompanying the decomposition of organic compounds.” Proc. R. Soc. B: Biol. Sci. 84 (571): 260–276.
Rathour, R., D. Patel, S. Shaikh, and C. Desai. 2019. “Eco-electrogenic treatment of dyestuff wastewater using constructed wetland-microbial fuel cell system with an evaluation of electrode-enriched microbial community structures.” Bioresour. Technol. 285: 121349.
Sajana, T. K., M. M. Ghangrekar, and A. Mitra. 2017. “In situ bioremediation using sediment microbial fuel cell.” J. Hazard. Toxic Radioact. Waste 21 (2): 04016022. https://doi.org/10.1061/(ASCE)HZ.2153-5515.0000339.
Sathe, S. M., and G. R. Munavalli. 2019. “Domestic wastewater treatment by modified bio-rack wetland system.” J. Water Process Eng. 28: 240–249.
Srivastava, P., S. Dwivedi, N. Kumar, R. Abbassi, V. Garaniya, and A. K. Yadav. 2017. “Performance assessment of aeration and radial oxygen loss assisted cathode based integrated constructed wetland-microbial fuel cell systems.” Bioresour. Technol. 244: 1178–1182.
Srivastava, P., A. K. Yadav, and B. K. Mishra. 2015. “The effects of microbial fuel cell integration into constructed wetland on the performance of constructed wetland.” Bioresour. Technol. 195: 223–230.
Tiwari, B. R., and M. M. Ghangrekar. 2015. “Enhancing electrogenesis by pretreatment of mixed anaerobic sludge to be used as inoculum in microbial fuel cells.” Energy Fuels 29 (5): 3518–3524.
Villaseñor, J., P. Capilla, M. A. Rodrigo, P. Cañizares, and F. J. Fernández. 2013. “Operation of a horizontal subsurface flow constructed wetland—microbial fuel cell treating wastewater under different organic loading rates.” Water Res. 47 (17): 6731–6738.
Wang, J., X. Song, Y. Wang, B. Abayneh, Y. Li, D. Yan, and J. Bai. 2016. “Nitrate removal and bioenergy production in constructed wetland coupled with microbial fuel cell: Establishment of electrochemically active bacteria community on anode.” Bioresour. Technol. 221: 358–365.
Watson, V. J., and B. E. Logan. 2011. “Analysis of polarization methods for elimination of power overshoot in microbial fuel cells.” Electrochem. Commun. 13 (1): 54–56.
Xu, L., Y. Zhao, L. Doherty, Y. Hu, and X. Hao. 2016. “Promoting the bio-cathode formation of a constructed wetland-microbial fuel cell by using powder activated carbon modified alum sludge in anode chamber.” Sci. Rep. 6 (1): 26514.
Yadav, A. K. 2010. “Design and development of novel constructed wetland cum microbial fuel cell for electricity production and wastewater treatment.” In Proc. 12th Int. Conf. on Wetland Systems for Water Pollution Control, 1085–1089. Venice, Italy: International Water Association (IWA).
Yadav, A. K., R. Abbassi, N. Kumar, S. Satya, T. R. Sreekrishnan, and B. K. Mishra. 2012a. “The removal of heavy metals in wetland microcosms: Effects of bed depth, plant species, and metal mobility.” Chem. Eng. J. 211–212: 501–507.
Yadav, A. K., P. Dash, A. Mohanty, R. Abbassi, and B. K. Mishra. 2012b. “Performance assessment of innovative constructed wetland-microbial fuel cell for electricity production and dye removal.” Ecol. Eng. 47: 126–131.
Yadav, A. K., S. Jena, B. C. Acharya, and B. K. Mishra. 2012c. “Removal of azo dye in innovative constructed wetlands: Influence of iron scrap and sulfate reducing bacterial enrichment.” Ecol. Eng. 49: 53–58.
Zhao, Y., S. Collum, M. Phelan, T. Goodbody, L. Doherty, and Y. Hu. 2013. “Preliminary investigation of constructed wetland incorporating microbial fuel cell: Batch and continuous flow trials.” Chem. Eng. J. 229: 364–370.
Zhi, W., and G. Ji. 2012. “Constructed wetlands, 1991–2011: A review of research development, current trends, and future directions.” Sci. Total Environ. 441: 19–27.

Information & Authors

Information

Published In

Go to Journal of Hazardous, Toxic, and Radioactive Waste
Journal of Hazardous, Toxic, and Radioactive Waste
Volume 24Issue 3July 2020

History

Received: Jul 28, 2019
Accepted: Nov 20, 2019
Published online: Mar 25, 2020
Discussion open until: Mar 25, 2020
Published in print: Jul 1, 2020

Permissions

Request permissions for this article.

Authors

Affiliations

M. Tech., Dept. Agricultural and Food Engineering, Indian Institute of Technology, Kharagpur 721302, India. ORCID: https://orcid.org/0000-0001-6141-4774. Email: [email protected]
Ph.D. Scholar, Dept. of Agricultural and Food Engineering, Indian Institute of Technology, Kharagpur 721302, India. ORCID: https://orcid.org/0000-0002-7628-4746. Email: [email protected]
Professor, Dept. of Civil Engineering, Indian Institute of Technology, Kharagpur 721302, India; Head, School of Environmental Science and Engineering, Indian Institute of Technology, Kharagpur 721302, India (corresponding author). ORCID: https://orcid.org/0000-0002-0691-9873. Email: [email protected]
Arunabha Mitra [email protected]
Professor, Dept. of Agricultural and Food Engineering, Indian Institute of Technology, Kharagpur 721302, India. Email: [email protected]

Metrics & Citations

Metrics

Citations

Download citation

If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.

Cited by

View Options

Get Access

Access content

Please select your options to get access

Log in/Register Log in via your institution (Shibboleth)
ASCE Members: Please log in to see member pricing

Purchase

Save for later Information on ASCE Library Cards
ASCE Library Cards let you download journal articles, proceedings papers, and available book chapters across the entire ASCE Library platform. ASCE Library Cards remain active for 24 months or until all downloads are used. Note: This content will be debited as one download at time of checkout.

Terms of Use: ASCE Library Cards are for individual, personal use only. Reselling, republishing, or forwarding the materials to libraries or reading rooms is prohibited.
ASCE Library Card (5 downloads)
$105.00
Add to cart
ASCE Library Card (20 downloads)
$280.00
Add to cart
Buy Single Article
$35.00
Add to cart

Get Access

Access content

Please select your options to get access

Log in/Register Log in via your institution (Shibboleth)
ASCE Members: Please log in to see member pricing

Purchase

Save for later Information on ASCE Library Cards
ASCE Library Cards let you download journal articles, proceedings papers, and available book chapters across the entire ASCE Library platform. ASCE Library Cards remain active for 24 months or until all downloads are used. Note: This content will be debited as one download at time of checkout.

Terms of Use: ASCE Library Cards are for individual, personal use only. Reselling, republishing, or forwarding the materials to libraries or reading rooms is prohibited.
ASCE Library Card (5 downloads)
$105.00
Add to cart
ASCE Library Card (20 downloads)
$280.00
Add to cart
Buy Single Article
$35.00
Add to cart

Media

Figures

Other

Tables

Share

Share

Copy the content Link

Share with email

Email a colleague

Share