Mechanistic Modeling and Process Design for Removal of Anionic Surfactant Using Dolochar
Publication: Journal of Hazardous, Toxic, and Radioactive Waste
Volume 24, Issue 3
Abstract
The rapid rise in consumption of surfactants day by day and the consequent increase in discharge from both industrial and residential areas into bodies of water has become a cause for concern. In this study, an industrial waste material (dolochar) was used for the removal of sodium dodecyl sulfate (SDS). Adsorption experiments were executed using batch and column mode. The experimental data were analyzed by various adsorption isotherm models, including: Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich (D-R). Out of these models, the Langmuir isotherm appeared to be the best fit (R2 = 0.97) and produced a maximum adsorption capacity of 5.78 mg/g at optimized conditions. The effect of different parameters, such as adsorbent dose, contact time, pH, agitation speed, and particle size, on SDS removal efficiency was investigated. It was observed that all the variables play important roles in affecting the amount of SDS adsorbed and, therefore, the removal efficiency. Maximum adsorption capacity of 98% was attained at an adsorbent dose of 16 g/L, near neutral pH, 150 rpm as the agitation speed and particle size below 300 μm. A column study was performed with three different adsorbent doses (and hence different bed depths) of 10, 20, and 30 g. A bed depth service time (BDST) model was selected to check its validity and column performance, and to scale up the process parameters. The logit method was also applied to calculate various associated parameters. Characterization of dolochar before and after adsorption was performed using scanning electron microscopy (SEM).
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors wish to acknowledge the Department of Civil Engineering and Bio-fuel & Bio-processing Research Center, Siksha “O” Anusandhan (Deemed to be University), Bhubaneswar; School of Infrastructure, Indian Institute of Technology, Bhubaneswar; and National Institute of Science Education and Research (NISER), Bhubaneswar for facilitating the research work.
References
Aboulhassan, M., S. Souabi, A. Yaacoubi, and M. Baudu. 2006. “Removal of surfactant from industrial wastewaters by coagulation flocculation process.” Int. J. Environ. Sci. Technol. 3 (4): 327–332.
Adak, A., M. Bandyopadhyay, and A. Pal. 2005a. “Removal of anionic surfactant from wastewater by alumina: A case study.” Colloid Surf., A 254 (1–3): 165–171.
Adak, A., A. Pal, and M. Bandyopadhyay. 2005b. “Spectrophotometric determination of anionic surfactants in wastewater using acridine orange.” Indian J. Chem. Technol. 12: 145–148.
Aloui, F., S. Kchaou, and S. Sayadi. 2009. “Physicochemical treatments of anionic surfactants wastewater: Effect on aerobic biodegradability.” J. Hazard. Mater. 164 (1): 353–359.
Ayranci, E., and O. Duman. 2007. “Removal of anionic surfactants from aqueous solutions by adsorption onto high area activated carbon cloth studied by in situ UV spectroscopy.” J. Hazard. Mater. 148 (1–2): 75–82.
Banerjee, S., and M. C. Chattopadhyaya. 2017. “Adsorption characteristics for the removal of a toxic dye, tartrazine from aqueous solutions by a low-cost agricultural by-product.” Arab. J. Chem. 10: S1629–S1638.
Bhandari, P. S., and P. R. Gogate. 2018. “Kinetic and thermodynamic study of adsorptive removal of sodium dodecyl benzene sulfonate using adsorbent based on thermo-chemical activation of coconut shell.” J. Mol. Liq. 252: 495–505.
Chaudhry, S. A., Z. Zaidi, and S. I. Siddiqui. 2017. “Isotherm, kinetic and thermodynamics of arsenic adsorption onto Iron-Zirconium Binary Oxide-Coated Sand (IZBOCS): Modelling and process optimization.” J. Mol. Liq. 229: 230–240.
Chowdhury, Z. Z., S. M. Zain, A. K. Rashid, R. F. Rafique, and K. Khalid. 2013. “Breakthrough curve analysis for column dynamics sorption of Mn(II) ions from wastewater by using Mangostana garcinia peel-based granular-activated carbon.” J. Chem. 2013: 1–8.
Dubinin, M. M., and L. V. Radushkevich. 1947. “Equation of the characteristic curve of activated charcoal.” Proc. Acad. Sci. USSR 55: 331–333.
Dwari, R. K., D. S. Rao, A. K. Swar, P. S. R. Reddy, and B. K. Mishra. 2012. “Characterization of dolochar wastes generated by the sponge iron industry.” Int. J. Min. Met. Mater. 19: 992–1003.
Foo, K. Y., and B. H. Hameed. 2010. “Insights into the modeling of adsorption isotherm systems.” Chem. Eng. J. 156 (1): 2–10.
Gupta, S., A. Pal, P. K. Ghosh, and M. Bandyopadhyay. 2003. “Performance of waste-activated carbon as a low-cost adsorbent for the removal of anionic surfactant from aquatic environment.” J. Environ. Sci. Health A 38 (2): 381–397.
Gupta, V. K., and Suhas. 2009. “Application of low-cost adsorbents for dye removal—A review.” J. Environ. Manage. 90 (8): 2313–2342.
Hutchins, R. A. 1973. “New method simplifies design of activated carbon systems.” Chem. Eng. 20: 133–138.
Jackson, M., C. Eadsforth, D. Schowanek, T. Delfosse, A. Riddle, and N. Budgen. 2016. “Comprehensive review of several surfactants in marine environments: Fate and ecotoxicity.” Environ. Toxicol. Chem. 35 (5): 1077–1086.
Jardak, K., P. Drogui, and R. Daghrir. 2016. “Surfactants in aquatic and terrestrial environment: Occurrence, behavior, and treatment processes.” Environ. Sci. Pollut. Res. Int. 23 (4): 3195–3216.
Koner, S., A. Pal, and A. Adak. 2011. “Utilization of silica gel waste for adsorption of cationic surfactant and adsolubilization of organics from textile wastewater: A case study.” Desalination 276 (1–3): 142–147.
Kundu, S., and A. K. Gupta. 2005. “Analysis and modeling of fixed bed column operations on As(V) removal by adsorption onto iron oxide-coated cement (IOCC).” J. Colloid Interface Sci. 290 (1): 52–60.
Langmuir, I. 1918. “The adsorption of gases on plane surfaces of glass, mica and platinum.” J. Am. Chem. Soc. 40 (9): 1361–1403.
Mahmoodi, N. M., A. Taghizadeh, M. Taghizadeh, and M. Azimi. 2019. “Surface modified montmorillonite with cationic surfactants: Preparation, characterization, and dye adsorption from aqueous solution.” J. Environ. Chem. Eng. 7 (4): 103243.
Maji, S. K., Y.-H. Kao, C.-J. Wang, G.-S. Lu, J.-J. Wu, and C.-W. Liu. 2012. “Fixed bed adsorption of As(III) on iron-oxide-coated natural rock (IOCNR) and application to real arsenic-bearing groundwater.” Chem. Eng. J. 203: 285–293.
Marsalek, R. 2011. “The adsorption of SDS on ferro-precipitates.” Int. J. Chem. Mol. Eng. 5 (10): 871–874.
McEvoy, J., and W. Giger. 1985. “Accumulation of linear alkylbenzenesulphonate surfactants in sewage sludges.” Naturwissenschaften 72 (8): 429–431.
Mirbahoush, S. M., N. Chaibakhsh, and Z. Moradi-Shoeili. 2019. “Highly efficient removal of surfactant from industrial effluents using flaxseed mucilage in coagulation/photo-Fenton oxidation process.” Chemosphere 231: 51–59.
Oulman, C. S. 1980. “The logistic curve as a model for carbon bed design.” J. Am. Water Works Assoc. 72 (1): 50–53.
Palmer, M., and H. Hatley. 2018. “The role of surfactants in wastewater treatment: Impact, removal and future techniques: A critical review.” Water Res. 147: 60–72.
Panda, H., S. Sahoo, N. Tiadi, R. R. Dash, and R. C. Mohanty. 2014. “Sorption of hexavalent chromium from synthetic waste water using dolochar.” J. Recent Res. Sci. Technol. 6 (1): 106–110.
Pandiarajan, A., R. Kamaraj, S. Vasudevan, and S. Vasudevan. 2018. “OPAC (orange peel-activated carbon) derived from waste orange peel for the adsorption of chlorophenoxyacetic acid herbicides from water: Adsorption isotherm, kinetic modelling and thermodynamic studies.” Bioresour. Technol. 261: 329–341.
Prokurat, S. 2015. “Drought and water shortages in Asia as a threat and economic problem.” J. Mod. Sci. 3 (26): 235–250.
Purakayastha, P. D., A. Pal, and M. Bandyopadhyay. 2005. “Sorption kinetics of anionic surfactant on waste tire rubber granules.” Sep. Purif. Technol. 46 (3): 129–135.
Que, W., L. Jiang, C. Wang, Y. Liu, Z. Zeng, X. Wang, Q. Ning, S. Liu, P. Zhang, and S. Liu. 2018. “Influence of sodium dodecyl sulfate coating on adsorption of methylene blue by biochar from aqueous solution.” J. Environ. Sci. 70: 166–174.
Rahmani, Z., and M. T. Samadi. 2017. “Preparation of magnetic multi-walled carbon nanotubes to adsorb sodium dodecyl sulfate (SDS).” Avicenna J. Environ. Health. Eng. 4 (1): e61902.
Rout, P. R., P. Bhunia, and R. R. Dash. 2015. “Effective utilization of a sponge iron industry by- product for phosphate removal from aqueous solution: A statistical and kinetic modeling approach.” J. Taiwan Inst. Chem. Eng. 46: 98–108.
Rout, P. R., P. Bhunia, and R. R. Dash. 2014a. “Modeling isotherms, kinetics and understanding the mechanism of phosphate adsorption onto a solid waste: Ground burnt patties.” J. Environ. Chem. Eng. 2 (3): 1331–1342.
Rout, P. R., R. R. Dash, and P. Bhunia. 2014b. “Modelling and packed bed column studies on adsorptive removal of phosphate from aqueous solutions by a mixture of ground burnt patties and red soil.” Adv. Environ. Res. 3 (3): 231–251.
Rozada, F., M. Otero, J. B. Parra, A. Morán, and A. I. García. 2005. “Producing adsorbents from sewage sludge and discarded tyres.” Chem. Eng. J. 114 (1–3): 161–169.
Scott, M. J., and M. N. Jones. 2000. “The biodegradation of surfactants in the environment.” Biochim. Biophys. Acta Biomembr. 1508 (1–2): 235–251.
Shami, S., R. R. Dash, A. K. Verma, A. K. Dash, and A. Pradhan. 2019. “Adsorptive removal of surfactant using dolochar: A kinetic and statistical modeling approach.” Water Environ. Res. 92: 222–235. https://doi.org/10.1002/wer.1193.
Sen, T. K., M. T. Thi, S. Afroze, C. Phan, and M. Ang. 2012. “Removal of anionic surfactant sodium dodecyl sulphate from aqueous solution by adsorption onto pine cone biomass of Pinus Radiate: Equilibrium, thermodynamic, kinetics, mechanism and process design.” Desalin. Water Treat. 45 (1–3): 263–275.
Suksabye, P., P. Thiravetyan, and W. Nakbanpote. 2008. “Column study of chromium (VI) adsorption from electroplating industry by coconut coir pith.” J. Hazard. Mater. 160 (1): 56–62.
Temkin, M. J., and V. Pyzhev. 1940. “Recent modifications to Langmuir isotherms.” Acta Physiochim. USSR 12: 217.
Uddin, M. T., M. Rukanuzzaman, M. M. R. Khan, and M. A. Islam. 2009. “Adsorption of methyleneblue from aqueous solution by jackfruit (Artocarpus heteropyllus) leaf powder: A fixed-bed column study.” J. Environ. Manage. 90 (11): 3443–3450.
United Nations. 2018. “World water development report.” Geneva: United Nations. Accessed March 20, 2019. https://www.unwater.org/publications/world-water-development-report-2018/.
Velinov, N., J. Mitrović, M. Radović, M. Petrović, M. Kostić, D. Bojić, and A. Bojić. 2017. “New biosorbent based on Al2O3 modified lignocellulosic biomass (Lagenaria vulgaris): Characterization and application.” Environ. Eng. Sci. 35 (8): 791–803.
Yadav, D., M. Kapur, P. Kumar, and M. K. Mondal. 2015. “Adsorptive removal of phosphate from aqueous solution using rice husk and fruit juice residue.” Process Saf. Environ. Prot. 94: 402–409.
Zhang, Y., F. Jin, Z. Shen, F. Wang, R. Lynch, and A. Al-Tabbaa. 2019. “Adsorption of methyl tert-butyl ether (MTBE) onto ZSM-5 zeolite: Fixed-bed column tests, breakthrough curve modelling and regeneration.” Chemosphere 220: 422–431.
Zhu, B. Y., and T. Gu. 1991. “Surfactant adsorption at solid-liquid interfaces.” Adv. Colloid. Interface Sci. 37 (1–2): 1–32.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Jul 9, 2019
Accepted: Oct 3, 2019
Published online: Mar 31, 2020
Published in print: Jul 1, 2020
Discussion open until: Aug 31, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.