Suspender Replacement for a Signature Bridge
Publication: Journal of Bridge Engineering
Volume 23, Issue 11
Abstract
The suspender is one of the most critical members for suspension bridges. Corrosion is the greatest degradation mechanism for suspenders during their service lives. Practices in North America have shown that the average time for the replacement of suspenders is between approximately 60 and 75 years. In this case study, three pairs of representative suspender ropes were removed and replaced on the Bronx–Whitestone Bridge, which was opened to traffic in 1939. The detailed suspender replacement procedure is presented. A refined three-dimensional (3D) finite-element (FE) model of the suspension bridge was developed to determine the jacking forces during replacement. To ensure that the new suspender tension reached a desirable value, an advanced vision-based sensor was adopted for noncontact force measurement, which eliminated the need for direct access to the suspender ropes to install conventional sensors. Subsequently, the existing suspenders that were removed were inspected visually. Three typical locations along suspenders, where dirt and water easily accumulate, were found to be especially vulnerable to corrosion: directly above the sockets, the section over the cable band, and at the suspender clamps. Finally, testing procedures are described to explain the estimation of the remaining ultimate strength of the removed existing ropes. The overall practices presented in this case study can help guide future suspender-rope replacements and investigations.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. 2017. AASHTO LRFD bridge design specifications. 8th ed. Washington, DC: AASHTO.
ASTM. 2013. Standard test method for tension testing of wire ropes and strand. A931-08. West Conshohocken, PA: ASTM International.
ASTM. 2014. Standard specification for zinc-coated steel structural wire rope. A603-98. West Conshohocken, PA: ASTM International.
ASTM. 2018. Standard test method for weight [mass] of coating on iron and steel articles with zinc or zinc-alloy coatings. A90/A90M-13. West Conshohocken, PA: ASTM International.
Cluni, F., V. Gusella, and F. Ubertini. 2007. “A parametric investigation of wind-induced cable fatigue.” Eng. Struct. 29 (11): 3094–3105. https://doi.org/10.1016/j.engstruct.2007.02.010.
Cunha, A., and E. Caetano. 1999. “Dynamic measurements on stay cables of cable-stayed bridges using an interferometry laser system.” Exp. Tech. 23 (3): 39–43. https://doi.org/10.1111/j.1747-1567.1999.tb01570.x.
Fang, Z., and J.-q. Wang. 2012. “Practical formula for cable tension estimation by vibration method.” J. Bridge Eng. 17 (1): 161–164. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000200.
Faust, D. G., M. Bulmer, B. Urbans, and D. Wilkinson. 2016. “Suspension bridge cable and suspender rope maintenance.” Chap. 6 in Inspection, evaluation and maintenance of suspension bridges, edited by S. Alampalli and W. J. Moreau, 157–198. Boca Raton, FL: CRC.
Feng, D., and M. Q. Feng. 2017a. “Experimental validation of cost-effective vision-based structural health monitoring.” Mech. Syst. Sig. Process. 88: 199–211. https://doi.org/10.1016/j.ymssp.2016.11.021.
Feng, D., and M. Q. Feng. 2017b. “Identification of structural stiffness and excitation forces in time domain using noncontact vision-based displacement measurement.” J. Sound Vib. 406: 15–28. https://doi.org/10.1016/j.jsv.2017.06.008.
Feng, D., M. Q. Feng, E. Ozer, and Y. Fukuda. 2015. “A vision-based sensor for noncontact structural displacement measurement.” Sensors 15 (7): 16557–16575. https://doi.org/10.3390/s150716557.
Feng, D., T. Scarangello, M. Q. Feng, and Q. Ye. 2017. “Cable tension force estimate using novel noncontact vision-based sensor.” Measurement 99 (Mar): 44–52. https://doi.org/10.1016/j.measurement.2016.12.020.
Gentile, C., and A. Cabboi. 2015. “Vibration-based structural health monitoring of stay cables by microwave remote sensing.” Smart Struct. Syst. 16 (2): 263–280. https://doi.org/10.12989/sss.2015.16.2.263.
Kanazawa, T., M. Shimomura, M. Okawa, Y. Kishi, and Y. Nagao. 2016. “Maintenance of suspension bridge suspender rope–replacement work and maintenance policy.” In Proc., 9th Int. Cable Supported Bridge Operators Conf. (ICSBOC), 378–387. Halifax, NS, Canada: Halifax Harbour Bridges and the International Cable Supported Bridge Operators Association.
Li, S., S. Zhu, Y.-L. Xu, Z.-W. Chen, and H. Li. 2012. “Long-term condition assessment of suspenders under traffic loads based on structural monitoring system: Application to the Tsing Ma Bridge.” Struct. Control Health Monit. 19 (1): 82–101. https://doi.org/10.1002/stc.427.
Lorentzson, J., Y. Chen, L. Hansen, P. McDonagh, J. Myszczynski, and D. Paskova. 2016. “Inspection of suspension bridges.” Chap. 3 in Inspection, evaluation and maintenance of suspension bridges, edited by S. Alampalli and W. J. Moreau, 69–102. Boca Raton, FL: CRC.
Mayrbaurl, R. M., and S. Camo. 2004. Guidelines for inspection and strength evaluation of suspension bridge parallel wire cables. NCHRP Rep. 534. Washington, DC: Transportation Research Board.
Nassif, H. H., M. Gindy, and J. Davis. 2005. “Comparison of laser Doppler vibrometer with contact sensors for monitoring bridge deflection and vibration.” NDT & E Int. 38 (3): 213–218. https://doi.org/10.1016/j.ndteint.2004.06.012.
Petrini, F., and F. Bontempi. 2011. “Estimation of fatigue life for long span suspension bridge hangers under wind action and train transit.” Struct. Infrastruct. Eng. 7: 491–507. https://doi.org/10.1080/15732479.2010.493336.
Port Authority of New York and New Jersey. 2015. “George Washington Bridge Rehabilitation Program.” Accessed October 1, 2017. https://www.panynj.gov/bridges-tunnels/restoring-the-george.html.
Sun, Z., S. Ning, and Y. Shen. 2017. “Failure investigation and replacement implementation of short suspenders in a suspension bridge.” J. Bridge Eng. 22 (8): 05017007. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001089.
Information & Authors
Information
Published In
Journal of Bridge Engineering
Volume 23 • Issue 11 • November 2018
Copyright
© 2018 American Society of Civil Engineers.
History
Received: Nov 16, 2017
Accepted: May 9, 2018
Published online: Sep 11, 2018
Published in print: Nov 1, 2018
Discussion open until: Feb 11, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.