Damage Mechanism of Control Springs in Modular Expansion Joints of Long-Span Bridges
Publication: Journal of Bridge Engineering
Volume 23, Issue 7
Abstract
Premature damage in modular expansion joints, especially in control springs, has been observed in several long-span bridges, which calls for an in-depth study on the damage mechanism. In this study, relative movements of lamellae at different locations of the expansion joints were measured in bridge service condition. It is found that the movements of lamellae were nonuniform, and lamellae near the approximately fixed end of the expansion joint showed much larger relative movements than center lamellae. As a result, control springs underneath these lamellae presented more severe damage than the others. To simulate the behavior of the expansion joint, a finite-element (FE) model was developed, through which the vertical load bearing, horizontal slide friction, and self-equivalence of lamella spacing were modeled, and static and dynamic FE analyses were conducted to obtain the responses of control springs at different locations. Finally, four control springs were tested in a laboratory, in which there was no damage under monotonic loading with shear deformation of 80 mm, whereas under high-cycle loading, two damage patterns were observed, i.e., falling off of the metal head and shear cracking in the rubber cylinder. As cyclic displacement amplitudes increased, the lives of control springs decreased significantly.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Support from the Natural Science Foundation of Jiangsu under Grant BK20130023 and the Education Department of Jiangsu under Grant JHB2012-1 is gratefully acknowledged.
References
AASHTO. (2012). “Section 14: Joints and bearings.” AASHTO LRFD bridge design specifications, 6th Ed., Washington, DC, 1–89.
ANSYS. (2005). ANSYS version10.0: User’s manual, Canonsburg, PA.
ANSYS 10 [Computer software]. ANSYS, Canonsburg, PA.
Baker Engineering and Energy. (2006). “Evaluation of various types of bridge deck joints.” Final Rep. 510, Arizona DOT, Phoenix.
Butterworth, S. (1930). “On the theory of filter amplifiers.” Wireless Eng., 7(Oct), 536–541.
Cao, Y., Yim, J., Zhao, Y., and Wang, M. L. (2011). “Temperature effects on cable stayed bridge using health monitoring system: A case study.” Struct. Health Monit., 10(5), 523–537.
CEN (European Committee for Standardization). (2004). “Structural bearings—Part 2: Sliding elements.” BS EN1337-2, Brussels, Belgium.
Chouw, N., and Hao, H. (2008). “Significance of SSI and nonuniform near-fault ground motions in bridge response I: Effect on response with conventional expansion joint.” Eng. Struct., 30(1), 141–153.
Crocetti, R., and Edlund, B. (2003). “Fatigue performance of modular bridge expansion joints.” J. Perform. Constr. Facil., 167–176.
Dexter, R., Osberg, C., and Mutziger, M. (2001). “Design, specification, installation, and maintenance of modular bridge expansion joint systems.” J. Bridge Eng., 529–538.
Ding, Y., Zhang, W., and Au, F. T. (2016). “Effect of dynamic impact at modular bridge expansion joints on bridge design.” Eng. Struct., 127(Nov), 645–662.
Feng, D., and Feng, M. Q. (2016). “Output-only damage detection using vehicle-induced displacement response and mode shape curvature index.” Struct. Contr. Health Monit., 23(8), 1088–1107.
Guo, T., Frangopol, D. M., and Chen, Y. (2012). “Fatigue reliability assessment of steel bridge details integrating weigh-in-motion data and probabilistic finite element analysis.” Comput. Struct., 112–113(Dec), 245–257.
Guo, T., Liu, J., and Huang, L. Y. (2016). “Investigation and control of excessive cumulative girder movements of long-span steel suspension bridges.” Eng. Struct., 125(Oct), 217–226.
Guo, T., Liu, J., Zhang, Y., and Pan, S. (2015). “Displacement monitoring and analysis of expansion joints of long-span steel bridges with viscous dampers.” J. Bridge Eng., 04014099.
MAGEBA. (2008). “Modular expansion joints– TENSA-MODULAR LR & LR-LS, Shanghai, China.
McCarthy, E., Wright, T., Padgett, J., DesRoches, R., and Bradford, P. (2014). “Development of an experimentally validated analytical model for modular bridge expansion joint behavior.” J. Bridge Eng., 235–244.
Roeder, C. W. (1998). “Fatigue and dynamic load measurements on modular expansion joints.” Constr. Build. Mater., 12(2), 143–150.
Sun, Z., and Zhang, Y. (2016). “Failure mechanism of expansion joints in a suspension bridge.” J. Bridge Eng., 05016005.
Zhao, Y., and Roddis, W. K. (2000). “Fatigue crack investigation for the Arkansas River bridge in Hutchinson, Kansas.” Constr. Build. Mater., 14(5), 287–295.
Information & Authors
Information
Published In
Journal of Bridge Engineering
Volume 23 • Issue 7 • July 2018
Copyright
© 2018 American Society of Civil Engineers.
History
Received: Sep 22, 2017
Accepted: Jan 15, 2018
Published online: Apr 24, 2018
Published in print: Jul 1, 2018
Discussion open until: Sep 24, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.