Primary Bond Mechanism Behavior of Posttensioned 7-Wire Strand during Load Exposition
Publication: Journal of Bridge Engineering
Volume 23, Issue 5
Abstract
The three primary bond mechanisms of a 7-wire strand are adhesion, friction, and mechanical interlocking between the concrete surface and the strands’ helical surfaces. Once adhesion fails as a result of micromovements of the strand, it is very difficult to predict the contribution of other two post-initial slip mechanisms to the total bond capacity of the 7-wire strand. The predictions become more difficult when the bond is influenced by the use of oil-based corrosion-protection (OCP) agents. This article discusses the influence of primary bond mechanisms during the loading stages of the posttensioned two-span concrete member and evaluates the contribution of bond mechanisms to the total member resistance and behavior. Elastomagnetic (EM) gauges, which can directly record the force inside the strands during prestressing and loading cycles, were used as one of the primary monitoring mechanisms. Based on these records, it is possible to evaluate force behavior in the strands during successive load stages up to the ultimate limit state (ULS) of the concrete members. The nonlinear bond behavior of the 7-wire strand is presented, including details of its elongation during testing.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The author gratefully acknowledges David Smith and Robert Petty (both of Atkins) for technical support and review. Special thanks is given to Associate Professor Andrej Jarosevic for the support and advice regarding EM gauge record evaluation. Sincere appreciation is also expressed to the Department of Concrete Structures at the Faculty of Civil Engineering at the Slovak University of Technology in Bratislava, Slovakia. The work was supported by the Slovak Research and Development Agency under Contract No. APVV-0442-12. The opinions, findings, and conclusions in this article are those of the author.
References
Borzovič, V., Laco, J., Pecník, M., and Pažma, P. (2016). “The crack development mechanism of prestressed girder influenced by different bond between prestressed tendons and concrete.” Key Eng. Mater., 691, 309–320.
BSI (British Standards Institution). (2000). “Concrete. Specification, performance, production and conformity.” BS EN 206-1:2000, London.
CEN (European Committee for Standardization). (2000). “Prestressing steels, part 3: Strand.” EN 10138-3, Brussels, Belgium.
CEN (European Committee for Standardization). (2004). “Design of concrete structures, part 1.1: General rules and rules for buildings.” Eurocode 2, EN 1992-1-1, Brussels, Belgium.
CEN (European Committee for Standardization). (2005). “Steel for the reinforcement of concrete. Weldable reinforcing steel: General.” EN 10080, Brussels, Belgium.
CEN (European Committee for Standardization). (2007). “Grout for prestressing tendons: Basic requirements.” EN 447, Brussels, Belgium.
Den Uijl, J. A. (1992). “Bond and splitting action of prestressing strand.” Proc., Bond in Concrete: From Research to Practice, Vol. 2, Comité Euro-international du Béton, Paris, 79–88.
EOTA (European Organization for Technical Assessment). (2002). “Post-tensioning kits for prestressing of structures.” ETAG 013, Brussels, Belgium.
FIB (Fédération Internationale du Béton). (2000). “Bond of reinforcement in concrete.” FIB Bulletin 10, Lausanne, Switzerland.
Halvonik, J., Dolnak, J., and Borzovič, V. (2013). “Long-term losses of prestress in precast members cast from HPC.” Procedia Eng., 65, 81–86.
Laco, J., and Borzovič, V. (2017). “Experimental investigation of prestressing strand bond on behavior of concrete members.” ACI Struct. J., 114(1), 15–24.
Laco, J., and Chrappa, M. (2016). “Corrosion protection material replacement in extradosed viaduct cables.” Proc., Performance-Based Approaches for Concrete Structures, FIB, Lausanne, Switzerland.
Laco, J., and Hendy, C. (2018). “Influence of oil-based corrosion protection on friction losses during strands installation and prestressing.” Proc., High Tech Concrete: Where Technology and Engineering Meet, FIB, Lausanne, Switzerland, 2299–2306.
Luthi, T., Diephuis, J., Icaza, J. J. Breen, J. E., and Kreger, M. E. (2005). “Factors affecting bond and friction losses in multi-strand post-tensioning tendons including the effect of emulsifiable oils.” CTR Research Report: 0-4562-1. Texas Dept. of Transportation, Austin, TX.
Martí-Vargas, J. R., Serna, P., and Hale, W. M. (2013). “Strand bond performance in prestressed concrete accounting for bond slip.” Eng. Struct., 51, 236–244.
Ryall, M. J., Parke, G. A. R., and Harding, J. E. (2000). The manual of bridge engineering, Thomas Telford, London.
Sumitro, S., Jarosevic, A., and Wang, M. L. (2002). “Elasto-magnetic sensor utilization on steel cable stress measurement.” Proc., 1st FIB Congress, FIB, Lausanne, Switzerland.
Information & Authors
Information
Published In
Copyright
© 2018 American Society of Civil Engineers.
History
Received: Jun 9, 2017
Accepted: Nov 14, 2017
Published online: Mar 13, 2018
Published in print: May 1, 2018
Discussion open until: Aug 13, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.